Is There a Way to Reset the Curt Converter Box on Vehicle Wiring Harness on 2003 BMW 325i Wagon
Question:
I have this part installed on my 2003 BMW 325I wagon. I use it to convert the tail lights for a small utility trailer. It worked fine for a few years then the last time I hooked up the trailer, I noticed that when my cars headlights are on, the blinkers on the trailer dont work. If I turn off the cars lights, the turn signals DO work. I probed the wires before the converter box and I get full intensity on the test light. But when I probe each wire after the converter box while the headlights are on, I get a almost undetectable intensity change on my LED tester. When I turn off the headlights I get full intensity from the turn signal on the test probe. I think my converter box is bad. Is there a way to reset the box by pulling the fuse, or is there a more heavy duty converter that is more reliable? I have had these converters fail before on other cars and they seem to be temperamental. But maybe it is just bad luck for me. BTW, I did not buy the part from your site, but am seeking your advise for a replacement because I have heard good things about etrailer.
asked by: Jerry B
Expert Reply:
It does sound like your converter box may be defective. Unfortunately, there is no way to reset the converter. I recommend trying to relocate the ground of the converter to see if this provides a solution to your problem. Grounding issues can show themselves in strange ways.
If relocating the ground doesn't fix your issue, I recommend replacing the wiring harness. For European cars like your BMW 325i Wagon, we've found we have the best success with the Upgraded Circuit Protected ModuLite with 4 Pole Harness and Hardwire Kit # C59496. This wiring harness upgrade will install using the existing power wire ran on your vehicle for the previous harness. I have attached a review video of this wiring harness for you.
I have attached the installation instructions for the # C59496 for you.
Product Page this Question was Asked From
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 8 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Fifth Wheel Hitch
- Shop: Curt Universal Fifth Wheel Base Rails with Installation Kit - Carbide Black Finish
- Shop: Curt A25 5th Wheel Trailer Hitch - Dual Jaw - 25,000 lbs
- Shop: Curt Custom 5th Wheel Installation Kit for Ford - Gloss Finish
- Shop: Replacement Hall Effect Motor for Lippert Components Ground Control 3.0 Leveling System
- Shop: On/Off Push Button Switch for RV Lighting - 4" Wire Leads - White/Gold
- Shop: Replacement Drive Head Bushing for Solera Power RV Awnings - Qty 1
- Shop: Lippert RV Slide-Out Motor by Klauber
- Shop: Trailer Wiring
- Q&A: Trailer Lights Stay on Once Vehicle Ignition is Shut Off
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
- Q&A: Recommended Wiring Harness For 2020 Toyota Tacoma Towing A Trailer
- Video: Choosing the Right Trailer Wiring
- Q&A: Working Running Lights, But No Turn Signals or Brake Lights On Trailer
- Q&A: Weight Capacity and Steel Standards for Curt and Draw-Tite Hitches for 2007 Honda FIt
- Shop: Trailer Hitch
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 90160
- Video: Choosing the Best Fifth Wheel Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer brake controller
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Video: Choosing the Right Brake Controller
- Article: Trailer Wiring Diagrams
- Search Results: brake controller
- Video: Tow Ready 4-Pole Mounting Bracket Installation
on Custom Fit Vehicle Wiring
