Where to Measure to Pick Out Replacement Spindle Washer

Question

Question:

I have a boat trailer. Single axle. 2006 lowe I changed the bearings and it did not have a washer on either side, I ended up getting 2 new hub kits but they did not come with washers either. Trying to figure out what washers I need. I could go to ace hardware but not sure if a plain washer would work ?

asked by: Steve

0

Expert Reply:

How big is the diameter of the spindle where the threads are? Most likely it's 1 inch and you would want the # SW1000 but you basically will just need to measure the spindle there and go with a washer that will fit it best.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For replacement bearings, races, and seals on your 2008 Airstream 19CB you need the following: -Bearings: Inner #25580 Outer #LM67048 -Races: Inner #25520 Outer #LM67010 -Grease Seal: #RG06-070 For grease you can use the LubriPlate Poly HP-2 Wheel…

view full answer...

Answer 2

Some Bearing Buddies have an Auto Check feature that uses a blue ring that will be flush with the top of the cylinder when full of grease. If it is not at the top you would add grease until the blue ring is pushed outward. If your Bearing Buddies do…

view full answer...

Answer 3

Overpacking the trailer hub with grease is the number one reason for grease seal failure. For a boat trailer I would recommend re-packing the hubs by hand with grease once per season and you'd be fine. I don't like recommending people use…

view full answer...

Answer 4

You can use the red grease #L11390 for trailer wheel bearings if you wanted. You can also use wheel bearing grease #L11465 which is designed for use on trailer running gear, including wheel bearings. It also has a slightly higher temperature rating,…

view full answer...

Answer 5

When installing electric over hydraulic brakes, disc or drum, going to a larger line would be fine but I would keep the size as consistent as possible to avoid any potential issues with a loss or increase in pressure from switching line sizes. If you…

view full answer...

Answer 6

The 1.75 inch inner diameter for bearing is #25580, which is only used on mostly 7,000 lb to 10,000 lb axles, as opposed to a 3,500 lb camper. Additionally, there isn't a hub with that bearing along with a bearing that has a 1.25 inch diameter,…

view full answer...

Answer 7

I believe I was able to find the bearings and seals that you need, but you'll want to double check on your end by removing the hub and looking at part numbers just to make sure. Inner Bearing - #25580 Inner Race - #25520 Outer Bearing - #02475…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Where to Measure to Pick Out Replacement Spindle Washer

Product Page this Question was Asked From

Continue Researching