Dimensions of Trailer Valet XL Ball Mount Height

Question

Question:

Hi Team, Curious to understand what the maximum height of the ball is? I want to understand how far I have to the coupler on my boat before I can connect it to the ball on the Trailer Valet. I have a Fulton X2 jack attached to the boat, so I need to be able to clear that when it is retracted. Thanks,

asked by: Josh A

0

Expert Reply:

Good news! I was able to go out to the warehouse and take a few measurements for you.

The Trailer Valet and the maximum height of the ball will be 20-1/4 inches from the ground. I also took the measurement from the center of the ball to the outer edge of the tire and it was 4-3/4 inches. This will give you a good idea of if your Fulton X2 will clear or not.

I have attached a diagram of the dimensions for your convenience.

expert reply by: Jackie C

0

click to enlarge

Answer 1

The instruction manual for the Trailer Valet XL Trailer Dolly with Chain Drive item #TVXL2 states not to use the dolly on any flat or paved incline or decline that is steeper than 10 degrees.

view full answer...

Answer 2

Yes, the Trailer Valet XL Trailer Dolly #TVXL2 does come with a drill attachment so that you could operate it with a power drill.

view full answer...

Answer 3

I've attached the photos of the instructions that come with the Trailer Valet XL Mounting Bracket #TVXLMB. It's a 2 page document, but hopefully it gives you a good idea of how it mounts and works with a Trailer Valet #TVXL2 or…

view full answer...

Answer 4

The Trailer Valet XL, part #TVXL2 with 2 inch ball and the #TVXL25 with the 2-5/16 inch ball are meant for use on level surfaces only, they wouldn't work well on the slope you describe.. Actually, I have a much less expensive and easier to use…

view full answer...

Answer 5

If you check out the review video I attached for the Trailer Valet XL #TVXL2 that you mentioned you can get an idea what conditions it can work in. We show it climbing a pretty steep incline as well as being used in gravel. It's hard to say if…

view full answer...

Answer 6

The Trailer Valet XL part #TVXL2 that you referenced can handle small inclines pretty well. If you check out the review video at the 2:30 mark you'll see the dolly being used to push a trailer up a pretty decent incline.

view full answer...

Answer 7

We do offer some replacement parts for the Trailer Valet, but it sounds like you have done some internal damage. The parts we offer are items like a crank handle #TV0006 or a Brake Cap And Steering Handle #TVBC. If there was damage done to the parts…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Dimensions of Trailer Valet XL Ball Mount Height

Product Page this Question was Asked From

Continue Researching