Using a Reducer Sleeve to Carry a 1-1/4 Inch Bike Rack in a 2 Inch Trailer Hitch

Question

Question:

I have an older model Thule Helium Aero rack with 1 1/4inch hitch. Is there an adaptor that I can buy to fit it to a 2inch hitch on my 2011 Ford Edge?

asked by: Barbara F

0

Expert Reply:

What you will need to use your Helium bike rack in a 2 inch trailer hitch is a reducer sleeve, # HT02. You would insert the sleeve into the hitch and pin it in place. Then you would mount the bike rack in the 1-1/4 inch end as if it were the hitch receiver. I have linked a video review of this reducer sleeve for you.

expert reply by: Michael H

0

Answer 1

50 percent is the general rule of thumb for hitch capacity reduction when using a hitch extender. An 8 inch extender would put less leverage on a hitch than an 18 inch extender, but instead of getting super particular with the percentage versus the…

view full answer...

Answer 2

I recommend using the Kuat Hitch Receiver Reducer Sleeve #KU93VR for the Thule T2 Pro XTR Bike Rack #TH83JV because it sits closer to the end of the hitch receiver so you'll have more than enough space for the AutoAttach system to work properly.…

view full answer...

Answer 3

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 4

In order to replace the bike lock cable on the Yakima HoldUp Bike Rack like part #Y02443 you will need to use the Replacement Cable Lock Assembly part #Y8890284. There would be no way to unlock the core you have now if the face was damaged but this…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...