Replacement 7-Way Recommendation for a 2008 Chevy Silverado with Rusted Out 7-Way Bracket

Question

Question:

I have a 2008 Silverado 1500 and the bracket in the bumper that holds the 7 pin connector has rusted to the point where the plastic connector is hanging free. Do you carry a bracket to replace the rusted OEM bracket? If not, what other options are there? Thanks!

asked by: Tom

0

Expert Reply:

To replace your 7-way on your 2008 Chevy Silverado 1500 you would want the part # 74682. This comes with a new bracket that you would want to attach to the bottom of your bumper. This also gives you a 4-way connector mounted on the side.

I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

There is power running to both sides at the same time on the Pollak 7- and 4-Pole Trailer Connector #HM40975. However, using both at the same time could result in over drawing power which could lead to blown fuses, electrical fire, accessories not…

view full answer...

Answer 2

Yes, the 7-way of the Reese Multi-Plug Wiring Harness for Factory Tow Package #74682 that you referenced does have a circuit that is designed for putting a maintenance charge on a trailer's battery. That pin is located in the 1:00 position of…

view full answer...

Answer 3

2005 Silverado models that came with a factory 7-Way plug, meaning 6 blades running around the edge and a round pin receptacle in the center, would not require additional connections to be made in order for the brake controller to function. If your…

view full answer...

Answer 4

When installing a trailer brake controller in a 2006 GMC Sierra that has a factory 7-way you will both plug in the controller at the under-dash port using the brand-specific wiring adapter AND make some connections under the hood at the power…

view full answer...

Answer 5

Most if not all trailer wiring harnesses/connectors use larger wires for the 12 volt and ground circuits compared to the other circuits (lights). The sockets themselves don't have an amperage rating so you will go by the draw of the things…

view full answer...

Answer 6

The Pollak 7-Pole connector #PK11916 is made for twist-in installation on OEM bumpers. We do not offer the metal OEM bracket part that this item fits into but that might be available at a dealership. What you can use is 7-way socket #A10-7072VP that…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...