Is It Required The Spring Seat Be Welded to Trailer Axle
Question:
I own a 2011 Jayco Jay flight swift trailer and I installed an axleflip kit no. K71-384-00 I did not weld it to the axle because I have no access to a welder. my question is does it require it to be welded or is it okay the way it is. the unloaded weight on the trailer is approx. 2,305. Any advise would be appreciated. Thank You
asked by: Mel C
Expert Reply:
It is highly recommended that the spring seat be at minimum tack welded to the axle. There have been issues that have resulted from the seat not be welded to the axle.
If you do not have access to a welder, I recommend taking the trailer to a local shop, possibly an auto repair shop, to have the seats welded to the axle.
Product Page this Question was Asked From
Dexter Trailer Springs Over-Under Conversion Kit
- Trailer Leaf Spring Suspension
- Alignment and Lift Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Round Axle - 2-3/8 Inch
- Single Axle
- Dexter
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Dexter Trailer Springs Over-Under Conversion Kit Installation K71-384-00
- Video: Review of Dexter Trailer Leaf Spring Suspension - U-Bolt Kit For 2000 lb Round Axle - APUBR-10
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Shop: Spring Seat for Typical 5,200-lb to 7,200-lb, Round Trailer Axles with 3" Diameter
- Video: Review of etrailer Trailer Axles - 60 Inch Long 2K Idler Axle - e48GR
- Shop: U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
- Q&A: How To Measure For Hub-Face And Spring Center Measurements On An Axle
- Shop: Shackle Strap - 2-1/4" Long
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Article: How to Raise Your Travel Trailer Height
- Search Results: leaf spring bushings
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Q&A: Does It Matter If the Spring Center and Hub Face Is Different When Replacing A Trailer Axle
- Search Results: cotter pin
- Search Results: shackle straps
- Q&A: Mounting Brackets to Use with Landing Gear Set # RVLG-8000
- Video: Review of Dexter Axle Trailer Axles - Leaf Spring Suspension - 8327820-EB
- Q&A: Proper Spacing Between the Hub Face and Spring Center Locations for 7,000-lb Triple Axles
- Q&A: Recommended Axle Installation with Spring Seats Too Wide for Spring Locations
- Q&A: What do the Hub Face and Spring Center Measurements Mean for an Axle
- Search Results: leaf spring
- Video: Redline Round Trailer Axle U-Bolt Mounting Kit Review
- Search Results: 13 trailer tire
- Search Results: bulldog hitch
- Search Results: ce17721
- Q&A: Should 2-1/4 Shackle Straps with New Suspension Kit be Used Instead of 3-1/2 Current Straps
- Article: How to Accurately Measure Trailer Leaf Springs
- Video: Review of Dexter Trailer Hubs and Drums - Hub with Integrated Drum - 8-407-5UC3-EZ
- Article: Where to Position the Trailer Axle?
on Trailer Leaf Spring Suspension
