Spindle Recommendation for a Hub that Has Bearing Dimensions 1.06 and 1.38

Question

Question:

Need a hub with a 1.0 outer and 1.35 inner spindle measurement with 5 4.5 wheel

asked by: Steven B

0

Expert Reply:

The spindle we offer that has the closest dimensions to what you listed will be an 84 spindle like part # TRU64FR. The surface of the spindle where the bearings will ride is 1.06 inch and 1.38 inch which is pretty close to what you have but not exact so you would want to double check the measurements you took.

For a hub then with the bolt pattern 5 on 4-1/2 inch like you said you need you would want the part # 84545BX.

expert reply by: Jameson C

0

Answer 1

I can help you find electric brake hubs for the M105A with a 6 on 5-1/2 bolt pattern. The bearings that come with the hubs fit the spindle based on the capacity of the axle on the M105A. From my research the M105A2 either uses a 5200 lb or 6000 lb…

view full answer...

Answer 2

For your Dexter Torflex 2,200 lb trailer axle the correct hub replacement is the #CE13109 which has a 4 on 4 inch bolt pattern like you need and also the correct bearing numbers of L44649. This is also pre-greased which means you have a super easy…

view full answer...

Answer 3

The best way to match hubs to an axle/spindle is going to be by finding a hub with the same size bearings as the ones that you removed; you can usually find numbers stamped on the backs of the bearings that designate their size. The Trailer Idler Hub…

view full answer...

Answer 4

The dimensions you mentioned mean the spindle on your trailer is a number 84 which is very common. So for a bearing kit that fits this you'll want the part #BK2-100. I attached an install video for this kit for you to check out as well.

view full answer...

Answer 5

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 6

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 7

The brake mounting bolt pattern for the #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles #TRU87FR is 2-13/16" and then the section that fits into the axle tube is 2" and it tapers out to 2-3/8". Attached are dimensional…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Answer 10

If you remove the hub and wipe away the grease on the spindle you can check to see if it is damaged. Look for an scarring, gouges, discoloration, or scoring on the spindle. If the spindle is damaged then the bearings won't ride properly and can…

view full answer...

Answer 11

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Spindle Recommendation for a Hub that Has Bearing Dimensions 1.06 and 1.38

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching