Availability of Follow Leg to Match the Lippert Components Lead Landing Gear Leg # LC179013

Question

Question:

The mounting tabs look to be on the back with the drive pin to the left. I need one with the drive pin and mounting tabs on opposite sides. Thanks

asked by: Bob B

0

Expert Reply:

The Lippert Components 29-1/2" Lead 5th Wheel RV Landing Gear Drop Leg # LC179013 is a lead leg. If you are looking for the opposite configured version of this leg you would need the follow leg part # LG-179014.

expert reply by: Jameson C

0

Answer 1

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin #LC179013 or the Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2" #LG-179013 will work to replace your Atwood lead leg. Atwood has…

view full answer...

Answer 2

The Lippert Components 29-1/2" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 that you referenced would bolt to a trailer if it currently has Lippert landing gear on it. This would attach to the trailer's current frame brackets. If your…

view full answer...

Answer 3

I can tell you how to find out if the Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 will fit your 2011 Dutchmen but trailer manufacturers don't keep specific parts lists that we would be able to cross-reference in…

view full answer...

Answer 4

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg part #LC179013 is only available as a complete unit. If any of the internal components have been damaged you will need to replace the entire leg.

view full answer...

Answer 5

To find out if the Lippert Components 32" Lead, part #LC179013, will work with your 5th wheel, you need to check your current one against this one to see if it matches. Key measurements of this leg are: Bracket Stop - 17-1/2" Height with…

view full answer...

Answer 6

Glad to hear how pleased you are with the Lippert landing legs #LC179013 and #LC179014! I spoke to my contact at Lippert and he recommended a white lithium grease like #L11354 for the zerk fitting for the gears and a silicone based lubricant on the…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Availability of Follow Leg to Match the Lippert Components Lead Landing Gear Leg # LC179013

Product Page this Question was Asked From

Continue Researching