How do Lippert Landing Gear Legs Attach to a Trailer Frame

Question

Question:

is this a weld-on?

asked by: Robinson

0

Expert Reply:

The Lippert Components 29-1/2" Lead 5th Wheel RV Landing Gear Drop Leg # LC179013 that you referenced would bolt to a trailer if it currently has Lippert landing gear on it. This would attach to the trailer's current frame brackets.

If your trailer has a different brand of jacks installed currently you would need to have the frame brackets moved if they are not 17-1/2 inches apart measured form the insides.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin #LC179013 or the Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2" #LG-179013 will work to replace your Atwood lead leg. Atwood has…

view full answer...

Answer 2

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg part #LC179013 is only available as a complete unit. If any of the internal components have been damaged you will need to replace the entire leg.

view full answer...

Answer 3

I can tell you how to find out if the Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 will fit your 2011 Dutchmen but trailer manufacturers don't keep specific parts lists that we would be able to cross-reference in…

view full answer...

Answer 4

To find out if the Lippert Components 32" Lead, part #LC179013, will work with your 5th wheel, you need to check your current one against this one to see if it matches. Key measurements of this leg are: Bracket Stop - 17-1/2" Height with…

view full answer...

Answer 5

The Lippert Components 29-1/2" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 is a lead leg. If you are looking for the opposite configured version of this leg you would need the follow leg part #LG-179014.

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

How do Lippert Landing Gear Legs Attach to a Trailer Frame

Product Page this Question was Asked From

Continue Researching