Is the Threaded Nut On the Lippert Components 32" Lead Landing Gear Drop Leg Replaceable

Question

Question:

Can I get this nut in parts or do I need to buy the complete leg? only thing bad is the nut. everything else is fine.

asked by: Richard D

1

Helpful Expert Reply:

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg part # LC179013 is only available as a complete unit. If any of the internal components have been damaged you will need to replace the entire leg.

expert reply by: Conner L

1

Answer 1

The Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg w/Snap Pin #LC179013 or the Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2" #LG-179013 will work to replace your Atwood lead leg. Atwood has…

view full answer...

Answer 2

To find out if the Lippert Components 32" Lead, part #LC179013, will work with your 5th wheel, you need to check your current one against this one to see if it matches. Key measurements of this leg are: Bracket Stop - 17-1/2" Height with…

view full answer...

Answer 3

The Lippert Components 29-1/2" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 is a lead leg. If you are looking for the opposite configured version of this leg you would need the follow leg part #LG-179014.

view full answer...

Answer 4

The Lippert Components 29-1/2" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 that you referenced would bolt to a trailer if it currently has Lippert landing gear on it. This would attach to the trailer's current frame brackets. If your…

view full answer...

Answer 5

I can tell you how to find out if the Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg #LC179013 will fit your 2011 Dutchmen but trailer manufacturers don't keep specific parts lists that we would be able to cross-reference in…

view full answer...

Answer 6

The Replacement Lead Leg #LC119102 will fit your Venture VMC900R landing gear. We also have the Follow Leg #LC119101 available if you wish to replace them both. The Leg #LC179013 you found is for LCI Power Landing Gear assemblies.

view full answer...

Answer 7

The difference in the repair kits for your VMC900R will be the Drive Shaft; a lead leg kit will have a different shaped shaft than the follow leg. The replacement Landing Gear Kit for Venture Follow Legs is #LC146060, while the Lead Leg repair kit is…

view full answer...

Answer 8

The part numbers you have provided indicates that the landing gear is a Venture system. For a replacement 33-1/2 inch lead leg use #LG-177202. For the gear box use #LG-179015. Current pricing is available on the product pages.

view full answer...

Answer 9

If you are looking for a way to convert your landing to a dual motor setup there's really no way to do that without replacing the follow leg with a lead leg, adding a motor and gear box, adding an additional switch and eliminating the cross…

view full answer...

Answer 10

The replacement follow leg replacement you need is the Lippert #LC179013 which works and is interchangeable with Venture landing gear legs like you have and has the correct outer tube height of 29-1/2 inches.

view full answer...

Answer 11

The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter #AM3200 that you referenced installs in a set of fifth wheel rails like the picture I attached shows. A bed liner would not interfere with this at all. See picture. If…

view full answer...

Answer 12

The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter - 20,000lbs Item #AM3200 will sit on the rails so it shouldn't be in contact with the bed liner. The only issue you might have is if the bed liner is raised too much and…

view full answer...

Is the Threaded Nut On the Lippert Components 32" Lead Landing Gear Drop Leg Replaceable

Product Page this Question was Asked From

Continue Researching