Grease Seals with Inner Diameter of 1.750-Inches

Question

Question:

im looking for a 1 3/4 id seal spindle wear sleeve do you have them

asked by: Mike M

0

Expert Reply:

We offer three grease seals that have a 1.750-inch inner diameter. You can see these by clicking on the link provided. The three seals have outer diameters of 2.312, 2.356 and 2.722-inches. You can use a digital caliper like # PTW80157 to measure your hub's bore to find out which seal is the proper fit. For example, part # 10-42 is a single-lip seal with an outer diameter of 2.33-inches meant for Dexter 2800-lb axles.

expert reply by: Adam R

0

Answer 1

I can certainly point you in the right direction. This will be a tricky one, as the Dexter 5,200 lb axles can use more than one seal size. We do not have the ability to pull an OEM build sheets to see what parts they installed at the factory so we…

view full answer...

Answer 2

The bearing kit you are looking for is the part #BK3-310. This includes the bearings and seals you mentioned so it would be exactly what you need.

view full answer...

Answer 3

When you use the Bearing Buddy Bearing Protectors like #BB2441, so you do not need to take apart the wheel hub and repack the bearings. The Bearing Buddy Protectors have a spring loaded seal that keeps the moisture and debris out of the bearings.…

view full answer...

Answer 4

Based on my research your Dexter 8-245 hub is a 3,500 lb hub that and the correct replacement inner bearing is part #L68149 with the matching race being part #L68111. The correct replacement outer bearing is part #L44649 and the matching race is…

view full answer...

Answer 5

The Tru-Ryde Grease Seal #RG06-050 that you referenced is a direct replacement for National Seal part 473336. This is a grease seal. The original part number you provided, 472193, is an oil seal, according to my research. It is specified to have an…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Grease Seals with Inner Diameter of 1.750-Inches

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching