Individual Parts for Trailer Suspension Hanger Kit APT1 without the Hangers

Question

Question:

I am replacing suspension on an older tandem axle horse trailer. I need 8inch straight equalizers and shackles, etc but I do NOT need the hangers. Is it possible to order APT1 kit but without the 6 hangers? Thank-you

asked by: Steven G

1

Helpful Expert Reply:

You can get the parts in hanger kit # APT1 separately but not as a kit minus the hangers. The equalizer is # TREQR83. For shackle straps you will need 8 of # 115052. For shackle bolts and nuts you would need 12 of # 166081. For the 3/4 inch wet bolts, pins, nuts, and grease fittings you would need 2 of # 126A1.

expert reply by: Michael H

1

Answer 1

If they are double-eye leaf springs, it should not matter which way they are facing. But if they are slipper springs, the eye end is at the front and the slipper is at the back. The springs that we carry are not marked as to which end is front and I…

view full answer...

Answer 2

The easiest way to accomplish this would be to start on one side of the trailer and get the springs in place before bolting the axle to the springs with the u-bolts. Have the axle up on jacks or blocks so its weight is not bearing on the springs.…

view full answer...

Answer 3

Any given tire size can have more than one load range. The load range represents the ply rating for a tire size and the higher the ply rating the higher the capacity of the tire. Plies are the structural components inside a tire. A tire can have…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...