Finish Used on Fulton Weld-On Trailer Jack Bracket Part # P9012-00

Question

Question:

Does the weld on bracket part # P9012-00 have a zinc finish on it?

asked by: Robert

0

Expert Reply:

The Fulton # P9012-00 weld-on trailer jack bracket has a raw steel finish. It's not zinc plated.

expert reply by: Mike L

0

Answer 1

The #F500349 Replacement Bolt-On Mounting Kit for Fulton XP Series Jacks comes with a single bolt, nut and washer for the center attachment point. There are no U-bolts included in this kit. If you are looking for the mounting hardware used with the…

view full answer...

Answer 2

I went out to our warehouse to take a look at the Fulton Replacement Bolt-On Mounting Kit #F500349 referenced in your question. I measured a distance between the two outside bolt holes, horizontally, of right at 5-1/2 inches. Vertically the distance…

view full answer...

Answer 3

I spoke with my contact at Fulton and he said that the Fulton F2 jack will not attach to the Fulton Jack Mounting Bracket, part #P9012-00. He said they are in the process of designing an adapter that will allow that, but it is only on the drawing…

view full answer...

Answer 4

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

I do have an option but Glo-Brite is no longer in business so you won't be able to get any replacement parts for these lights such as lenses. The only option you have would be a full replacement for which the most similar option we offer is the…

view full answer...

Answer 8

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't reset. He…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

You mentioned a 20 ton (40000 lbs) tag trailer with disc brakes. If you have a 20 ton trailer it would most likely come with air brakes. Next, you mention a tandem axle trailer with two 10000 lb axles and disc brakes, so I am thinking you were…

view full answer...

Answer 11

Sorry to hear about the troubles you're having! To remove the Alpha Systems 4034 Roof Coating for RV Roofs #AL34CV from the side of your 1998 Tiago, you can use: - A type of chemical paint remover, - A Paint scraper tool, - A Pressure washer, Or…

view full answer...

Answer 12

The prep you mentioned is more than adequate prior to applying the Alpha Systems 4034 Roof Coating for RV Roofs #AL34CV. According to the instructions you only need to apply the Primer #AL77CV if you're applying this to an EPDM membrane. In that…

view full answer...

Finish Used on Fulton Weld-On Trailer Jack Bracket Part # P9012-00

Product Page this Question was Asked From

Continue Researching