Are the Trailer Wheel Bolts RG02-020 Galvanized

Question

Question:

RG02-020 Are these wheel bolts galvanized, or available as such? Or perhaps in stainless steel?

asked by: Chris B

0

Expert Reply:

I checked with my contact at Redneck and he confirmed that these Wheel Bolts # RG02-020 are zinc plated which is very similar to galvanization.

expert reply by: Jameson C

0

Answer 1

We confirmed recently with our contact at Dexstar that the capacity of the Dexstar Steel 8-Spoke Trailer Wheel #AM20522 is 2,150 lbs. For the highest capacity rim in the size you need this would be the one. It is made in the USA.

view full answer...

Answer 2

Yes, the Wheel Bolts, #RG02-020, are 1/2-20 bolts which seems to be the standard for many hubs, drums, and wheels. They also have the industry standard 60 degree cone and are fine threaded.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

The difference between the two trailer tire sizes is that the letter D in the first size you listed ST205/75D15 stands for bias ply and the letter R in the tire size that they put on your vehicle stands for radial. Radial tires are preferred over…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Are the Trailer Wheel Bolts RG02-020 Galvanized

Product Page this Question was Asked From

Continue Researching