Rear Sway Bar Recommendation for a 2002 Workhorse W20

Question

Question:

Hello, I am getting conflicting info on this bar for my 36 foot Winnebago on a W20 Workhorse chassis. Will this work? I think it should and would be better because of my length

asked by: Jim M

0

Expert Reply:

For your 2002 Workhorse W20 chassis you would want the part # RM-1259-108 as a rear sway bar and not the # RM-1259-109 that you referenced.

expert reply by: Jameson C

0

Answer 1

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 2

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 3

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 4

The air suspension system on your 2022 Ram 2500 limits your options for suspension enhancement. None of the air bags made for your truck will be compatible. Instead, I recommend adding the SumoSprings Rebel Custom Helper Springs #SS64VR. The…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 7

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 8

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 9

I found the online version of the install instructions for the Exact Center stabilizers like the #RM47MR. What's fun is that just when you think you have found the correct step to address your problem it tells you to continue to the next step.…

view full answer...

Answer 10

Hi there David; we do have truck camper jacks that can work for your F-250 with a lift and large tires. What you can use are camper jacks from Brophy, which have a 17" to 67" lift range, which is the highest possible lift height. There are…

view full answer...

Answer 11

For your 2024 Ford F-53, I recommend checking out the Timbren Front Suspension Enhancement System #TFFF53B for the front, and the Timbren Rear Suspension Enhancement System #TFRF53A for the rear. These kits do not require drilling, will replace your…

view full answer...

Answer 12

According to RoadActive Suspension the spring rate for the standard kit #RAS3611-S is 2,400 lbs. For the heavy duty #RAS3611-SHD it is 3,600 lbs. The heavy duty #RAS3611-SLHD is the same but only designed to fit if you have factory top overload…

view full answer...