Trailer Hitch and Wiring for a 2016 Honda HR-V

Question

Question:

Is there a trailer hitch and some wiring that will fit my 2016 Honda HR-V, NOT a CR-V, different cars.

asked by: John

0

Expert Reply:

Yes, for your 2016 Honda HR-V you can use the Curt trailer hitch # C11416. Ball mount # 3593 is the correct ball mount if you intend to do any light duty towing. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258.

And for trailer wiring you can use # C56284 to add a 4-Way trailer connector.

If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch.

If you need to carry more than 2 bikes or need a 300 pound tongue weight instead of a 200-pound capacity, you could instead install the EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - 2" # 306-X7322 which is also a confirmed fit for your HR-V.

expert reply by: Michael H

0

Answer 1

The Curt Class I hitch, part #C11416 has a shipping weight of 19 pounds. So, the hitch weighs around 16 pounds. If you're planning on using the hitch as a mounting point for a bike rack or a cargo carrier (and you probably are), remember that…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 9

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...