Can a Trailer Spindle with Grooves Still be Used if Bearing Fits
Question:
I removed the hubs on my trailer to repack the bearings and found grooves worn into the bottom side of one spindle. The grooves are located where the inner and outer bearings would sit on the spindle. The grooves are too big to be addressed with emory cloth. However, the bearings fit well. Do I need to replace the spindle or can I continue to use this spindle?
asked by: David P
Expert Reply:
You will have to replace the spindle. Grooves that can't be taken out with emory cloth will eventually cause new bearings to fail which will leave you stranded with a locked up wheel most likely.
To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel tracking problems. I would recommend finding a welder who is experienced with trailer axles. Your local RV dealer or repair facility could probably refer you.
Product Page this Question was Asked From
Square BT8 Spindle for 2,000-lb Trailer Axles - 1-1/2" Wide
- Trailer Spindles
- Standard Spindle
- 1-1/2 Inch Diameter
- Square
- For 2000 lb Axle
- TruRyde
more information >
Continue Researching
- Article: Most Popular Wheel Bearings
- Shop: CE Smith U-Bolt Kit for Mounting 2" Square Trailer Axles - 4-1/2" Long U-Bolts - Zinc
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Shop: Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 95" Long - 3,500 lbs
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter
- Search Results: brake line
- Search Results: brake lines
- Search Results: trailer brake lines
- Search Results: brake line clips
- Video: Yates Rubber Boat Trailer Parts - Roller and Bunk Parts - YR5213-5 Review
- Video: Review of Trailer Leaf Spring Suspension - Spring Mounting Hardware - 166079
- Video: etrailer Trailer Brakes - Hydraulic Drum Brakes - AKFBBRK-35-D Review
- Q&A: What is the Proper Torque Range for Trailer Wheels
- Q&A: Comparing the E-Z Lube Hubs to the Standard Hub Assemblies for Trailer Axles
- Q&A: Bolt Hole Spacing of 4-Bolt Brake Mounting Flange for 10 Inch 3,500 Pound Hydraulic Brake Kit
- Shop: Spring-Eye Bolt with Locknut for Slipper Springs - 3-1/2" Long
- Shop: Suspension Enhancement
- Q&A: Is There Differnce Between Trailer Grease Seals 10-36 and GS-2250DL
- Search Results: e52gr
- Search Results: 95 axle
- Search Results: 3500 trailer axles
- Video: Titan Premier Disc Brake Kit Installation
- Article: Trailer Tire Sizing
- Video: CE Smith Trailer Hub Assembly Review and Installation
- Video: Review of TruRyde Washer For 1 Inch Spindle - SW1000
- Q&A: Is a Damaged Spindle Safe to Use If Hub Fits It
- Q&A: Washer and Nut to Use with CE Smith Trailer Hub # CE13109
- Q&A: How to Determine the Size of a Trailer Hub Assembly for Replacement
on Trailer Spindles
William
1/14/2020
what if grooves are small and can be knocked down with emery cloth? what are tolerances on a 1 spindle?