Washer and Nut to Use with CE Smith Trailer Hub # CE13109

Question

Question:

Hello, I am looking at purchasing two of the hubs but do not see a thrust washer listed, does it come with one? if not, can you recommend the correct one? greatly appreciate all your help,

asked by: Richard

0

Expert Reply:

The CE Smith Trailer Hub Assembly part # CE13109 does not come with a spindle nut or washer so if you needed that as well you'd need the # RG05-100 which is a it for both sides of the axle that includes washers and nuts.

expert reply by: Jameson C

0

Answer 1

It might seem that the spindle being slightly bent isn't a big deal but it can definitely lead to another blowout so you'll want to replace that spindle with a new one. It looks like you have a straight spindle like the standard BT8…

view full answer...

Answer 2

You will have to replace the spindle. Grooves that can't be taken out with emory cloth will eventually cause new bearings to fail which will leave you stranded with a locked up wheel most likely. To replace a spindle, the old one would need…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 7

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub…

view full answer...

Answer 8

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 9

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 10

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 11

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any…

view full answer...

Answer 12

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Washer and Nut to Use with CE Smith Trailer Hub # CE13109

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching