Correct Curt Manufacturing 5th Wheel Install Frame Brackets for 2000 Ford F350 w/ 8 Foot Bed

Question

Question:

WILL THIS FIT MY TRUCK?

asked by: DRAYTON B

0

Expert Reply:

For your 2000 Ford F350, the correct frame mounting bracket kit would be part # C16443. For the frame bracket/ bed rail kit, use part # C16443-204.

If you already have Curt bed rails, you can certainly use the # C16443 by itself, but we don't recommend using frame brackets and bed rails from different manufacturers. They WILL fit, but since they haven't been tested together, using brackets from one manufacturer and rails from another could yield an unknown weight capacity, which would be unsafe.

The C16424 bracket you referred to is for a later-model F250/350 and wouldn't fit your truck.

If you don't already have a 7-way installed in your truck bed, you can install one using part # HM40157

expert reply by: Mike L

0

Answer 1

Yes, you can install a Curt Custom Install Kit with the Air Lift Airbags, but rather than the part number you referenced you will actually need the kit part #C16448-204 for your 2008 Ford F-250 With the way your Air Lift Airbags are installed, they…

view full answer...

Answer 2

I spoke to my contact at Curt and he said that the air bags that are installed on your 2001 Ford F350 are compatible with the Curt Custom Fifth Wheel Bracket Kit #C16443. To install both at the same time you will need to first remove the air bags,…

view full answer...

Answer 3

We have an air bag suspension enhancement kit that fits your 2000 Ford F-250 that is also compatible with an in-bed hitch with the Firestone part #F2550 but the Air Lift you mentioned is not it. There isn't a longer bolt solution or anything…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 8

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 9

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 10

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 11

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 12

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...