Install Information for the Prodigy P3 Brake Controller

Question

Question:

Tekonsha Prodigy P3 Trailer Brake Controller, Need install directions. Looked on line and could not locate them.

asked by: Gregg H

0

Expert Reply:

I attached an install link for the Prodigy P3 brake controller part # 90195 that you referenced as well as a couple help articles that detail how to hardwire in a brake controller.

I also attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

There are times when it is tough to locate the brake controller plug under the dash. On the 2015 Ram the factory plug is located between the brake pedal and the emergency brake pedal as shown in the attached photo. It is probably behind another…

view full answer...

Answer 2

Yes, we do have a generic brake controller wiring diagram on our Brake Controller Information page. I have added a link to it below. The bundle of wires you are looking for should contain the following: white with red stripe, blue with white stripe,…

view full answer...

Answer 3

What you'll need to install like our best selling P3 part #90195 in your 2007 Dodge Ram with a 4-way is the install harness part #3020-P and the #37185. Brake (blue) wire does not run all the way back to the 4-pole at the rear; it stops at the…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 8

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 9

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 10

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 11

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...