Where is the Length of a Sidewinder Arm Measured From

Question

Question:

Length of the pin box arm is measured from where to where?

asked by: Daryl

0

Expert Reply:

The length of the Sidewinder like part # RP34FR that you referenced is 22 inches. This is measured from the center of the turret (the pivot point on the base of the Sidewinder), to the center of the king pin.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The best fitting fifth wheel rail kits are the custom fit kits as they don't require frame drilling and the install time will be about half the time when compared to a universal kit. For your 2009 Dodge Ram 1500 the kit I recommend then is the…

view full answer...

Answer 2

For your 2010 Toyota Tundra with a 5-1/2 foot bed, you will need to use a stationary trailer hitch, like #RP30047 with installation kit #RP30035-309, and a sidewinder in order to have enough clearance to execute 90 degree turns safely. I have…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 8

Yes, you are going to also need the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 when using the Demco Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550040 with your Road Armor pin box. For a suspension enhancement I…

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Where is the Length of a Sidewinder Arm Measured From

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching