Replacement 800-lb Fulton Swivel Jack for 1995 Shorelandr Boat Trailer

Question

Question:

Hi..I have a Shorelandr Boat Trailer..1995 with Lund Pro V Boat. My jack Broke and can not find replacement. It is a Fulton Part number #3310050 - 800 pound swivel jack with the 2 bolts. Looks like Shorelandr has used these for years. Do you sell them? Thanks.

asked by: Jim

0

Expert Reply:

We can help you select a replacement jack for your 1995 Shorelandr boat trailer.

The linked page will let you see all Fulton brand side-of-frame-mount swivel jacks which are offered in lift capacities from 400 to 2000-lbs and in both weld-on and bolt-on types. Lift height is either 10-inches or 12-inches. For example, Fulton # FXPD15L is a 1500-lb 12-inch lift jack with dual wheels that bolts on to a 3 x 5-inch trailer frame.

It is always a good idea to use a jack rated higher than your trailer's actual loaded tongue weight since this usually means easier cranking and a longer working life for the jack since it will not be operated at its full capacity.

expert reply by: Adam R

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 6

Unless you want to completely clean out every bit of grease you will need to stick to a LMX red grease like item #L11390 that comes with the CE Smith Trailer Idler Hub Assembly item #CE13515. You can use your blue marine grease but you can't mix…

view full answer...

Answer 7

For your Shelby 5856A boat trailer, I recommend the Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - 12" Lift - 1,500 lbs #FXPD15L. This jack has zinc plating for corrosion resistance and durable poly wheels. For the single…

view full answer...

Answer 8

To determine which hubs would be best for your boat trailer there are a few things you will need to look at; the axle capacity on your boat trailer, the inner bearing number, outer bearing number, grease seal number, the bolt pattern of your wheels,…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

I think you are on the right track. The Fulton Bolt-Thru Swivel Marine Jack you mentioned, part #F1411300301, is rated at 1500 lb. With the jack fully retracted, the distance from the bottom of the mounting bracket to the floor is 12.5". I think…

view full answer...

Answer 11

Swapping the mounting hardware on a jack can be done, but it will depend on the specific mounting hardware of the jacks. Shelby jacks and parts are becoming more difficult to locate, so I would recommend replacing your Shelby hardware with something…

view full answer...

Answer 12

The Magnum name isn't used anymore, but the jack hasn't changed much. You'll be needing part #FXP15L for a 12 inch lift or #FXP15W for a 10 inch lift.. If you click the provided link, you can see a product description video fearing the…

view full answer...

Replacement 800-lb Fulton Swivel Jack for 1995 Shorelandr Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching