Would the Classic Accessories Toy Hauler Screen # 052963799842 Work with a Cable Ramp Spring

Question

Question:

I have a trailer that has the cables affixed to the ramp door that lead to the spring loaded system just inside at the top. Could I still use this system?

asked by: Jourdan B

0

Expert Reply:

The Classic Accessories Toy Hauler Screen # 052963799842 should fit your trailer fine. You would have to install it below the ramp door spring setup so that it doesn't interfere with it.

expert reply by: Jameson C

0

Answer 1

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 2

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 3

M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have 1/2"-20 Lug Nuts…

view full answer...

Answer 4

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

According to my research, your 92865A-1 hub/drum has a 25580 inner and an 14125A outer bearing and a 8 on 6-1/2 inch lug pattern, as does the AxleTek #AKHD-865-7-2-K hub drum you referenced. The #AKHD-865-7-2-K would be an acceptable replacement for…

view full answer...

Answer 7

Please note the attached instructions. The Lippert Anti-Billowing Kit for Solera Slide Topper Awnings, #LC78FR should be installed on the end of the awning that is closest to the front of the unit. 1. Make sure awning is fully retracted. 2. Place the…

view full answer...

Answer 8

I recommend to use the Solera 16-1/2' Slider part #LCV000435661 which matches the boxes width exactly so you will not have side overhang like we normally recommend but it is the biggest slide topper available to fit the 198" width of your…

view full answer...

Answer 9

We have toppers that'll work for 2 of your 3 sliders. For your 12 foot 9-1/2 slide, use #LCV000168109 which is designed for slides measuring between 152-157 inches wide. The longest topper we offer is for slides 188-193-3/4 inches, so…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 12

I recommend the Solera RV Slide-Out Awning - 13'1" Wide - 48" Projection #LCV000168109 which will fit RV's with slide outs that are 152" to 157" wide and up to 48" long, the awning rail is included. This is also…

view full answer...

Would the Classic Accessories Toy Hauler Screen # 052963799842 Work with a Cable Ramp Spring

Product Page this Question was Asked From

Continue Researching