Keyed Alike Flush Mount Locking Door Latches

Question

Question:

Can I get one set of keys for a set of 4 flush mount locking door latches? Would not want 4 different keys. Thx

asked by: Rod C

0

Expert Reply:

I called my contact at Redline, and they told me that they use the same lock and key for their flush mount door latches. So you could order 4 of part # L1883 and they would all be keyed alike. If you need a larger latch, 4 of part # L3980 would also be keyed alike. Both of these flush mount locking door latches use the same key number.

expert reply by: Victoria B

0

Answer 1

You are going to have to measure the thickness of your door. I wish there was a way to determine the thickness of a trailer door by looking at the VIN or elsewhere, but that info isn't something a trailer manufacturer would list somewhere since…

view full answer...

Answer 2

The Full Size Locking Steel Flush Door Latch #L3980 that you referenced can fit doors that are up to 1-1/6 inches thick. It would have no problem fitting yours that is 1 inch thick. This latch requires a hole size that is 3-3/8 inch by 4-5/8 inches.

view full answer...

Answer 3

Per the manufacturer, MORryde, "Actual tray width is 1/4? less than sizes listed. This allows the tray to fit inside the door opening. E.g. a 20? wide tray will fit inside a 20? wide door opening." The actual overall width of the MORryde…

view full answer...

Answer 4

We have a couple options close to 45 inches long for slide-out tray assemblies that may work for you. These are rail kits that have a 1,000 lb capacity but do not come with the plywood bottom, that is something you would need to configure. The good…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To create barn doors out of your ramp door, you will need hinges and a latch. I suggest a latch/lock system like the Universal Cam-Door Lock for Enclosed Trailers - 1" Keeper, #383200. This will use a 3/4 inch diameter pipe that you'll have…

view full answer...

Answer 7

If the hole in your door for the handle measure 2-3/4" x 3-3/4" the #L4080 would work, but most likely you would need a handle like the part #L1883 as that is more like the latching style of your current handle. This latch installs in the…

view full answer...

Answer 8

The #CHK510 key you mentioned is common to all #L1980, #L1930, #L1883, #L1833, and # L4080 latches. In order to get you the correct key, look on the face of the lock and see if there's a reference number engraved or stamped next to the key slot.…

view full answer...

Answer 9

I have attached for you below a dimensional drawing of the Square Corner Hinge with Reverse Bracket part #PLR2212-SSP provided from the manufacturer. This is the only dimensional drawing we offer for this product but if there is something else you…

view full answer...

Answer 10

I can help you out with parts to create a hatch in the floor of your enclosed trailer, but we don't have an all-in-one kit for an escape hatch in your trailer. You'd need to make a cut out in the floor of your trailer and then you can use the…

view full answer...

Answer 11

The best option I have for you is the Redline Weatherstrip Tape part #WS1434 which measures 3/4" wide x 1/4" thick x 50' long. This weatherstripping has an adhesive backing so you should be able to make it work for you in place of what…

view full answer...

Answer 12

The Redline Flush Mounted Door Latch, #L3980, will mount in a door that has a 3-3/8 x 4-5/8 inch mounting hole. This latch is rust proof and will attach to the door using screws instead of pop rivets. If this latch cannot fit into your door's…

view full answer...

Keyed Alike Flush Mount Locking Door Latches

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching