Trailer Fender with Lights Recommendation

Question

Question:

Hi. I need this exact fender, but with lights on the front and back One red and one Amber. Do you happen to carry that part? I have attached a pic of the fender I need replaced. It is for the left side of the trailer if you are sitting forward in the boat. Thanks!

asked by: Glenda F

0

Expert Reply:

You could likely cut out light holes on fender # F008575 if you wanted to. Using a rotary tool would make it quick and easy. Or you could mount left fender light # BA44FNL and right fender light # BA44FNR on the fenders. Fenders with pre-cut light holes are not available from us.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…

view full answer...

Answer 2

We have a very close option with the #CE19503-2 which is off by only 1/4 of an inch to the measurements you listed. It measures 29-3/4 inch for the inside portion and 33-3/4 inch for the outside portion.

view full answer...

Answer 3

The simplest option would be to install the Correct Track Trailer Alignment and Lift Kit #LC87120 on your trailer. This will allow you to raise the trailer frame from the axle 1-1/4" or 2-1/4". It will also allow you to shift the axle so it…

view full answer...

Answer 4

We do have a selection of fenders for 13" wheels that you can use to replace your current fenders. Among our linked selection we have different constructions like aluminum, plastic, and steel. These fenders can mount via brackets or welding…

view full answer...

Answer 5

I went out to our warehouse to take a look at both the CE Smith Single Axle Trailer Fenders - 12" Grey #CE19502-2 and the larger 13" Black #CE19503-2. Both options represent the only color available from CE Smith in the respective sizes.…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Trailer Fender with Lights Recommendation

Products Referenced in This Question

Continue Researching