Replacement Uprights for 60 CE Smith Boat Trailer Guide Ons

Question

Question:

Can I order just the steel posts? Thats the only part that wears out and falls apart from rust. The PVC and hardware are fine and dont need to be replaced.

asked by: Mark C

0

Expert Reply:

We have the part you are looking for. For the replacement metal upright for the CE Smith Post-Style Guide-Ons # CE27640 that you referenced you would want the part # CE27605PG.

expert reply by: Jameson C

0

Answer 1

The dimensions of the Replacement Upright for CE Smith Bunk-Style Guide-Ons #CE27605PG are 39 inches tall by 23 inches long. The tube is 1-1/2 inches and the bend is a 90 degree angle. I've attached a picture for you as well.

view full answer...

Answer 2

Though The Replacement Upright for CE Smith Bunk-Style Guide-Ons #CE27608PG is just short the next step up would be The Replacement Upright for CE Smith Bunk-Style Guide-Ons #CE27605PG is 39 inches. I attached a review video link below.

view full answer...

Answer 3

The Replacement Upright for CE Smith Bunk-Style Guide-Ons for Boat Trailers - Lanced - 39" #CE27605PG will absolutely help more than the angled posts for the visual to help you center your boat on the trailer, but they aren't designed to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Uprights for 60 CE Smith Boat Trailer Guide Ons

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching