Dimensions of the Brake Mounting Flange # 4-44-1

Question

Question:

what is the thickness from the bolt holes to the hole. what is the measurment ftom the center of the top bolt to the center of the 2 3/4 axle hole

asked by: Dylan

0

Expert Reply:

I went and pulled a Brake Mounting Flange # 4-44-1 from our warehouse to measure it for you and found that from the center of the studs to the inside edge of the center hole it measures 1/2 of an inch and then from the center of the top bolt down to the center of the hole it measures 2 inches.

expert reply by: Jameson C

0

Answer 1

The trailer will have a plate or sticker on it that will list the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that will list the weight capacity. You can…

view full answer...

Answer 2

The bolt pattern for a 5 bolt brake mounting flange, like #4-44-1 is 5 on 3-7/8 inches. What that means is it measures 3-7/8 inches from one corner to its diagonal counterpart. From hole to hole across the bottom is 3 inches and between the others is…

view full answer...

Answer 3

By bolt pattern, it seems like you may be referring to your hubs but the 5-bolt pattern is actually referring to a brake mounting flange like in the accompanying photo. A 5-bolt flange will look like Brake Mounting Flange for 3" Round Axle…

view full answer...

Answer 4

When installing the 12" Nev-R-Adjust Electric Brake Assembly, #23-459, you would need Brake Mounting Flange, #4-44-1. I have included a picture with measurements listed. Welding of a brake mounting flange is a precision job that requires the…

view full answer...

Answer 5

The bracket for mounting a jack on a A-frame trailer has a bolt pattern of 3 inches. The bolt holes may be different sizes which is why you'll see the slotted holes on a jack like #EJ-3520-BBX. This is the standard pattern for nearly all A-frame…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Dimensions of the Brake Mounting Flange # 4-44-1

Product Page this Question was Asked From

Continue Researching