Bolt Pattern of 5 Bolt Brake Mounting Flange for Trailer Brakes
Question:
I have an oddball question. On the standard 5 hole brake backing plate mounting flange, what is the center to center spacing between the bolt holes? I understand that the standard 5 bolt flange is an industry standard for trailer axles with 5 bolt patern but I would like to know what that standard is. Thank you,
asked by: Keith H
0
Expert Reply:
The bolt pattern for a 5 bolt brake mounting flange, like # 4-44-1 is 5 on 3-7/8 inches.
What that means is it measures 3-7/8 inches from one corner to its diagonal counterpart. From hole to hole across the bottom is 3 inches and between the others is about 2-1/8 inches.
I've made a diagram that may help.
expert reply by:
Charles S
0
Product Page this Question was Asked From
Brake Mounting Flange for 3" Round Axle
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Brake Mounting Flange
- 12 Inch
- 3 Inch Diameter Axle
- Redline
more information >
Continue Researching
- Shop: Brake Controller
- Search Results: grease seal
- Search Results: 12 brake drum
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Installation - 2022 Jeep Wagoneer
- Shop: Trailer Wiring
- Q&A: Are All 5-Bolt Brake Mounting Flanges the Same
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Video: Redline Tires and Wheels 25-11 Review
- Shop: Easy Grease Trailer Hub and Drum Assembly for 5.2K & 6K Axles - 12" - 6 on 5-1/2 - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Mounting Bolts and Hardware for 12" Brake Assemblies
- Shop: Brake Mounting Flange for 3" Round Axle
- Shop: Karrier ST235/85R16 Radial Trailer Tire w/ 16" White Wheel - 8 on 6-1/2 - Load Range F
- Shop: Provider ST235/80R16 Radial Tire w/ 16" Vesper White Mod Wheel - 8 on 6-1/2 - Load Range G
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Search Results: trailer brakes
- Search Results: a frame jack
- Search Results: vertical channel adapter
- Search Results: kar kaddy
- Search Results: demco brakes
- Q&A: Do Trailer Drums have to be Turned when Replacing Electric Trailer Brake Assemblies
- Q&A: Will Out of Adjustment Trailer Brakes Cause a Fault Code on the Electric Trailer Brake Controller
- Q&A: Comparing etrailer and Dexter Axle 12" Electric Brake Kits
- Q&A: Is Brake Magnet Supposed to Continuously Ride on Armature Surface of Brake Drum
- Q&A: Braking Assembly Recommendations For A 2017 Grand Design Momentum 395M
- Video: Review of Dexter Lubricants Sealants Adhesives - Multi Purpose Lithium Grease 14 OZ - DX64TR
- Video: etrailer Trailer Brakes AKBRKR-SP Review
- Shop: RV Roof Membrane
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
Jon
3/28/2024
Hi I have a older 6 lug 6 lb axles the bolts all measure the same across like you're saying but the center hole is like three and a quarter would that work for the center hole it's a three axle trailer and the guy when I bought it said it was around early 70s thanks for info