How to Install a Brake Controller in a 2012 Ford Van with a 4-Way Connector

Question

Question:

I have a 2012 Ford E-150 XLT. I have already installed a brake controller and need to add the wiring for the hitch plug in. I purchased the 118261 connector then discovered my van only has the plug for the flat four 118260. Will I be able to use the brake controller with the flat four plug, or is there a way to adapt the van for the 118261 so that I can use the brake controller?

asked by: Jared

0

Expert Reply:

We have what you would need, but there's no way to run a brake controller through a 4-way and you wouldn't be able to use the # 118261.

Instead all you would need is the part # ETBC7. This comes with everything needed to convert the 4-way to a 7-way and wire in your brake controller. Check out the install video and instructions links I attached.

expert reply by: Jameson C

0

Answer 1

Wiring for your 2011 Thor Majestic 23A on Ford E-350 Chassis will depend on whether or not you have the factory tow package/ports, which it sounds like you do. For a 7-way you would need the T-One Vehicle Wiring Harness for Factory Tow Package -…

view full answer...

Answer 2

Yes, there is a brake controller port on most 2012 Ford E-350's. If you take a look under the driver dash up by the emergency brake pedal you should see a four pin plug which is used for this purpose. I recommend the Tekonsha Primus IQ Trailer…

view full answer...

Answer 3

The first place that I recommend checking when you lose power to something would be your fuse box. A blown fuse can cause the power to not reach your brake controller. If your fuses look okay then it might be easier to find a wire that is connected…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

How to Install a Brake Controller in a 2012 Ford Van with a 4-Way Connector

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching