Location of Brake Controller Port on 2010 Dodge Ram For Tekonsha Brake Control Adapter, # 3021-P,

Question

Question:

where is the port for the brake controller on a 2010 dodge ram 1500 anyone have a photo

asked by: john g

0

Expert Reply:

The brake controller harness is located under the dash on the drivers side, just left of the steering column, and near the emergency brake pedal. See picture at the right.

I am sending a link on the installation instructions on a 2010 Dodge Ram. It shows the location of the factory port, for the plug in of the Tekonsha Brake Control Adapter - 2010 Dodge, # 3021-P, on your 2010 Dodge Ram 1500.

expert reply by: Jeff D

0

click to enlarge

Answer 1

If you try to use two regulators you will most likely have too low of pressure you run your propane accessories. We had a customer come back who tried to use a RV gas grill that was regulated from a propane source that was already regulated and the…

view full answer...

Answer 2

This sounds like the trailer brakes are not receiving the signal from the brake controller when you apply the brakes. I believe what is happening is that you may have a loose, broken, or inaccurate connection on the red wire from the brake…

view full answer...

Answer 3

The Hopkins Agility Trailer Brake Controller part 47295 and the Curt TriFlex Trailer Brake Controller part #C24VV are both fine options and very similar in their proportional design. That said, I recommend the Curt TriFlex because it's…

view full answer...

Answer 4

Brake controllers such as the P3 you referenced #90195 will go into a sleep mode after about 15 minutes of it sensing no movement. If you peek through the window after 15 minutes then it should be in sleep mode. Opening the door or causing movement…

view full answer...

Answer 5

That has to be a brake controller issue. Sounds like the controller is backfeeding the stoplight circuit it taps into as a signal wire with voltage which is then activating your brake lights. When this happens the brake controller is in need of being…

view full answer...

Answer 6

It sounds like there is either no power going to the black power wire on the Hopkins Agility Brake Controller, #HM47295, or the power wire is connected to the wrong circuit. I would recommend using a circuit tester, like part #PTW2993, to test the…

view full answer...

Answer 7

You might want to check the hitch on your 2010 Dodge Ram 2500, but it is usually welded on to the frame of your vehicle. It would be very difficult to remove. I would recommend the Curt Class V 2 Inch Hitch, part #C15409. This hitch has 17000 lbs…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Location of Brake Controller Port on 2010 Dodge Ram For Tekonsha Brake Control Adapter, # 3021-P,

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching