Fit of Fulton Single Axle Trailer Fender # F008551

Question

Question:

I am highly interested in purchasing part number F008551, however the fenders on my trailer are 21.5 long where the ones listed on here are showing 21.80 inches, which is a .30 of an inch difference, would this mount up exactly at the factory fenders or would I need to mock up brackets to make it work for the difference in length, everything else in measurement is the same but the length is the only difference between the two fenders, Thanks again.

asked by: Mike

0

Expert Reply:

The Fulton Single Axle Trailer Fender you referenced, part # F008551, is likely to fit your existing fender mounts since the overall difference in length is a modest 0.3-inches. But since there are so many trailer and mounting bracket designs it is hard to say with 100-percent certainty. This fender will have a certain amount of flex that would probably enable you to use a little "English" on it to get the right fit. You may want to install new or adjust your fender mounting brackets but this might not be essential.

I prepared for you a photo of the fender with the dimensions and spacing of its mounting holes to help you estimate the fit on your trailer.

expert reply by: Adam R

0

click to enlarge

Answer 1

To determine the amount of rise/drop you'll need, take a measurement from the inside top edge of the hitch receiver tube to the ground. Then, measure from the bottom of the trailer coupler to the ground. The difference between the two numbers…

view full answer...

Answer 2

The CE Smith Single Axle Trailer Fenders w/ Skirts - Gray Plastic - 8" to 12" Wheels - Qty 2 #CE19500-2 can be installed using the Mounting Brackets for Trailer Fender - 8" to 12" Wheels - Pre-Galvanized Steel - Qty 2 #CE26065PGA…

view full answer...

Answer 3

With the use of a cargo carrier a transmission cooler is not normally used, but a cooler will prolong the life of a transmission towing or not so it's a great idea for your 2014 Honda Odyssey. We installed the Derale part #D13502 on a 2014 Honda…

view full answer...

Answer 4

The Timbren Axle-Less Trailer Suspension System - Straight Spindle Only - 3,500 lbs #ASR3500S05 has a deflection of 1-3/4 inches. I've attached a photo to assist. We recommend 4 inches above the tire in most cases for fender mounting to account…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Fit of Fulton Single Axle Trailer Fender # F008551

Product Page this Question was Asked From

Continue Researching