Do the 10" x 1-1/2" Electric Brake Shoe/Lining # bp04-065 Fit Both Sides of Trailer

Question

Question:

I would like to confirm that these brakes shoes will fit either side or do I need to specify? Thank you

asked by: Sonny

0

Expert Reply:

The 10" x 1-1/2" Electric Brake Shoe/Lining # bp04-065 that you referenced can be used on both the right and the left had side brake assemblies normally seen on Dexter 2.8K axle.

expert reply by: Jameson C

0

Answer 1

What you were told was only partially correct. If you wanted to replace the entire brake assembly but you had welded on brakes then you could not replace the assemblies. However, you can replace the worn brake parts. There should be a number on the…

view full answer...

Answer 2

There a few things that you can do to figure out what the correct electric brake assembly you will need for your application. First, will be to figure out your axle weight capacity. This can sometimes be found on axles themselves or you can measure…

view full answer...

Answer 3

If you are looking for 10-inch by 1-1/2 inch brake shoes we have one option, #BP04-065. They fit Dexter 2.8K axles. Also, in most cases replacing the brake assemblies will be less expensive than replacing the shoes. If you need grease seals too I…

view full answer...

Answer 4

Looks like you have a welded on brake assembly that possibly could have the brake shoes replaced with the part #BP04-065 which is for an older Dexter 10" by 1-1/2" setup that was made before 1999. See if you can find "Dexter"…

view full answer...

Answer 5

Good news, we do have availability on those brake shoes. The part mumber for the 10" x 1-1/2" Electric Brake Shoe/Lining is BP04-65. The shoes are sold individually.

view full answer...

Answer 6

You may be able to replace the 10 x 1-1/2 inch electric brakes on your trailer with the more common sized 10 x 2-1/4 inch assemblies. The potential issue is the Dexter 2.8K axle that your existing electric brakes are mounted to. This particular axle…

view full answer...

Answer 7

Based on the images with the measurements you sent the Brake Shoe/Lining #bp04-065, Brake Spring Set #K71-362-00, and Magnet Kit #AKBRKR-M10 are the correct replacement parts for the brakes on your 1998 Nash 20N. We do have the Brake Mounting Flange…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Do the 10" x 1-1/2" Electric Brake Shoe/Lining # bp04-065 Fit Both Sides of Trailer

Product Page this Question was Asked From

Continue Researching