Does Replacement Hand Wheel Lock for Model 6 and 60 Actuator Come with Spring

Question

Question:

does it come with the spring? if not, how can I get a new spring? thank you

asked by: Steve

0

Expert Reply:

The replacement Hand Wheel Lock for Model 6 and 60 Actuator, # T2338300, contains one hand wheel lock and does not come with a spring. For replacement springs you will want the Latch Repair Kit for Titan Multi-Fit Couplers and Brake Actuators # T4045400.

expert reply by: Chris O

0

Answer 1

The Coupler Repair Kit part #C25194 is designed for Curt trailer couplers that use a 2" hitch ball. Since you have a Fulton trailer coupler I cannot recommend you use this kit. Instead, I recommend taking a look at part #F670801 which is…

view full answer...

Answer 2

I have a great solution to lock your trailer but the multi-fit couplers, and especially the one you have, are hard to fit coupler locks on. Your best option would then be the Rack'Em Wheel Lock part #RA-25 which will lock the trailer and…

view full answer...

Answer 3

We do carry the exact replacement latch for the Titan Model 60 Brake Actuator you referenced. The latch by itself is the Replacement Ball Latch #T4335800 and there is also the Latch Repair Kit #T4045400 which will work.

view full answer...

Answer 4

I spoke with my contact at Titan, and he said that your Zinc-Plated Coupler #T2343400183 with the handwheel and the Titan Leverlock Coupler #T4845000 are manufactured differently, so the mechanisms are not interchangeable. You will not be able to…

view full answer...

Answer 5

While there is not a rebuild kit for the Titan Model 60 brake actuator, we do have several replacement parts available. Replacement Master Cylinder Assembly for Drum Brakes - part #T439510 Replacement Push Rod Assembly for Brake Actuator - part…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...