Would the Kuat Beta # B202-2 fit 2 inch Hitch of a 2014 Subaru Forester

Question

Question:

are you aware of any issues with using the kuat alpha 2inch receiver on a 2014 subaru forester?

asked by: Marta

0

Expert Reply:

The Kuat Beta # B202-2 that you referenced would work great in the 2 inch hitch of your 2014 Subaru Forester. The newer Subaru 1-1/4 inch hitches do have issues fitting hitch bike racks and require the use of Yakima bike racks, but the 2 inch hitches like what you have would work just fine.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 8

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 9

Hello again Michelle. The Saris Glide EX Bike Rack #SA774 will indeed fit a 2023 Hyundai Tucson with a class 3 hitch. The tilt feature will allow the hitch to open and close normally. Saris bike racks are definitely good quality. They are all made…

view full answer...

Answer 10

The Tow Defender #RM-4700 you found is really our best option to protect the front of your 2024 Chevrolet Trax. This screen helps to deflect any road debris back down to the ground to keep it traveling under your Trax. This particular cover is…

view full answer...

Answer 11

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport Rider SE…

view full answer...

Would the Kuat Beta # B202-2 fit 2 inch Hitch of a 2014 Subaru Forester

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching