Mounting Hole Dimensions of the B and W Hitch part # BWHDRH25122
Question:
On B and W hitch, part number BWHDRH25122, What are the measurements between the front and the rear mounting holes? I see that it is a 5 1/2 inch , is that from the mounting flanges to the top of the receiver? I am looking to install it on a Ford F53 motorhome chassis with 34inch frame rails. I could use a 4 1/2 if one is available. Any info would be helpful. Thank you for your time,
asked by: Robert M
0
Expert Reply:
The distance from the center of the front hole to the center of the rear hole is 17-3/16 inches, and then the distance from the center of the rear hole to the middle hole is 5-3/4 inches.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 1600 lbs TW
- 16000 lbs GTW
- 16000 lbs WD GTW
- 2 Inch Hitch
- 1600 lbs WD TW
- Visible Cross Tube
- B and W
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Article: How Much Trailer Can I Really Tow
- Video: Trailer Hitch Installation - 1986 Chevrolet C/K Series Pickup - B&W
- Shop: Base Plate for Tow Bar
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Article: How to Choose the Right Trailer Hitch Class
- Video: Trailer Hitch Installation - 1988 Ford F-250 - B and W
- Shop: Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Q&A: Can The B&W Heavy-Duty Trailer Hitch BWHDRH25122 Clear An Aftermarket Bumper On A 1986 Chevy K20?
- Shop: Suspension Enhancement
- Video: Curt Gooseneck - Below the Bed - C60713 Review
- Q&A: Mounting Hole Dimensions for B&W Heavy-Duty Trailer Hitch Receiver, part # BWHDRH25122
- Q&A: Dimensions of Draw-Tite Ultra Frame Trailer Hitch Receiver # 41947
- Q&A: What is the Width of the Horizontal Plates That Mount to the Vehicle Frame on the Draw-Tite 41947
- Video: Review of CURT Heavy Duty Receiver Hitch - Weld-On Hitch - C87CR
- Video: Review of Curt Heavy Duty Receiver Hitch - Adjustable Weld-On Hitch - 15902
- Video: Review of CURT Heavy Duty Receiver Hitch - Weld-On Hitch - C37CR
- Q&A: Trailer Hitch Needed for a 2008 Ford F-350 is a Stake Bed Truck with Rear Liftgate
- Q&A: Bolt Spacing Dimensions B and W Hitch for 2001 Ford Cab and Chassis Truck
- Q&A: Will Blue Ox Class V Hitch Fit 1995 GMC C/K Pickup Cab And Chassis Truck With Lift Gate
- Search Results: universal hitch
- Video: Trailer Hitch Installation - 1997 Ford F-250 - Curt
- Shop: Brake Controller
- Search Results: curt class v
- Search Results: awning