Hitch for 2015 Toyota Highlander That Will Not Protrude Past Bumper

Question

Question:

2015 Toyota Highlander XLE I read in the Reviews that some of the hitches stick out past the bumper, and are real shin knockers. Are the reviewers correct in regards to shin knockers? Thank you,

asked by: Ernie

1

Helpful Expert Reply:

The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"# e98844 that you referenced does not stick out from the bumper it is almost exactly flush with the back of the bumper, so you would not need to be worried about accidentally banging your shins the receiver. You can see this set up at the 1:30 mark in the attached installation video.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Since hitch bolts are torque-to-yield like with the etrailer hitch part #e98844 that you referenced it is not required that you retorque the hardware. Just one to spec and you're good.

view full answer...

Answer 2

The etrailer hitch part #e98844 is a confirmed fit for your Highlander since your spare is steel. The magnet test you performed proves it is steel since it wouldn't stick to aluminum. The aluminum wheel spare is just too wide which is why they…

view full answer...

Answer 3

The spare tire for a 2019 Toyota Highlander is stored under the vehicle. If you check out the attached installation video for the etrailer Trailer Hitch Receiver #e98844 you can see the empty location under the vehicle where the spare tire should be.…

view full answer...

Answer 4

The etrailer hitch #e98844 is my recommendation for your 2019 Toyota Highlander. Because of that I think it's the obvious choice for your Highlander. It has an attractive black matte finish, a great towing capacity, and can be used with a weight…

view full answer...

Answer 5

If you take a look at the accompanying photo you can see our installer point out the exact location where you need to install the fuse in your 2018 Toyota Highlander when installing the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...