Can the Armature Surface of an Electric Drum Brake Hub Be Turned Like the Brake Surface
Question:
John thank you for the tolerance on the brake shoe braking surface. can the magnet surface of the drum be resurfaced also. if so, how much? thank you
asked by: Aaron P
Expert Reply:
The part of a hub/drum assembly that makes contact with the electromagnet, the armature surface, cannot be machined. If the surface is deteriorated you'd do well to replace that hub.
The link provided will show you all hub/drum assemblies which you can sort using the filters on the page. Be sure to match your bearing set, bolt pattern and axle weight capacity when choosing a new hub.
You might also refer to the linked article on re-packing bearings.
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 6 on 5-1/2
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Testing Trailer Brake Magnets for Proper Function
- Video: Solera Replacement Awning Fabric Review
- Video: Solera Replacement Awning Fabric Measurement and Installation
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Video: Dexter Axle Trailer Brakes BP01-110 Review
- Shop: RV Roof Membrane
- Video: etrailer Trailer Brakes - Electric Drum Brakes - AKEBRK-35-SA Review
- Shop: Replacement 11'1" Fabric for 12' RV Awning - Universal - Sand Fade w/White Weatherstrip
- Shop: Replacement 11'1" Fabric for 12' RV Awning - Universal - White Fade
- Shop: Replacement Brake Shoes for Dexter 10" Nev-R-Adjust Electric Brake - Right Hand - 3,000 lbs
- Video: etrailer Electric Trailer Brake Kit Installation
- Video: etrailer Trailer Brakes AKBRKR-M10 Review
- Q&A: Will the Installation Set for Bearing, Races, and Seals Work With Timken Bearings, Races, and Seals?
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Search Results: axletek 10" x 2 1/4" electric brake assembly
- Video: ProGrip Cam Buckle Lashing Straps Review
- Q&A: Recommended Tool To Use When installing Bearings In Hub
- Q&A: Correct Replacement for Dexter Electric Trailer Brake Assemblies 023-476-00
- Q&A: Troubleshooting Grease Seal that Keeps Blowing Out on Trailer Axle
- Q&A: Recommended Upgrade Replacement for BAL Stabilizer Jacks
- Q&A: Replacing 10x1-1/2 Inch Brake Assemblies with 10x2-1/4 Inch Brake Assemblies
- Q&A: Do Trailer Drums have to be Turned when Replacing Electric Trailer Brake Assemblies
- Search Results: dexter torsion axle lift kit
- Search Results: nev r lube bearings
- Search Results: k71~997~00
- Search Results: 008~247~05
- Search Results: 10 "brake drums
- Search Results: lm67010
on Trailer Hubs and Drums
