Correct Replacement Threaded Hitch Pin for Yakima BuckHorn 4 Bike Rack

Question

Question:

I need a 1/2” threaded hitch bolt for a Yakima Buckhorn 4” receiver. Can you help me? Thanks,

asked by: Peter

0

Expert Reply:

The correct replacement threaded hitch pin for the Yakima BuckHorn 4 Bike Rack is the Replacement Hitch Bolt and Clip for Yakima HoldUp and BigHorn Bike Carriers part # Y8890200.

expert reply by: Conner L

0

Answer 1

Thanks for the picture of hitch pin, but what was really helpful was actually the set of instructions you have in the background. Based on that you have the first version of the BigHorn which was made around 2001 and the correct hitch pin…

view full answer...

Answer 2

If I understood your question correctly it sounds like you are asking about the diameter of the very end of the Replacement Hitch Bolt #Y8890200. I went and pulled this from our warehouse to measure it and found it to be 3/8 of an inch. If you are…

view full answer...

Answer 3

The part #Y8890200 is 4-1/2 inches long which may be longer than what you currently have since some of the pins are only 4 inches long.

view full answer...

Answer 4

I went and pulled a Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier #Y8890200 from our warehouse to measure and found that the bolt has 5/8 inch coarse threads and the size wrench you would need to use to tighten it…

view full answer...

Answer 5

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Correct Replacement Threaded Hitch Pin for Yakima BuckHorn 4 Bike Rack

Product Page this Question was Asked From

Continue Researching