Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
Drilling required for installation
Trimming of front air dam and/or fascia may be required for installation
More Information >Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers, and more.
Installation Notes:
No drilling required for installation
Front air dam will have to be trimmed or removed
More Information >Videos
for Front Receiver Hitch
Help Articles
for Front Receiver Hitch
Expert Answers
for Front Receiver Hitch
From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy…
view full answer...I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…
view full answer...There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…
view full answer...Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…
view full answer...I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part #LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch…
view full answer...The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your Tahoe…
view full answer...I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have not…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have 1/2"-20 Lug Nuts…
view full answer...You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…
view full answer...The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Kevin
Manchester, MD