Yes, we have tons of replacement parts for the etrailer 4,900-Watt Portable Inverter Generators 333-0001-0002, some of which are listed for you below. These etrailer branded inverter generators are made by a company called Firman which have a longstanding reputation for quality manufacturing.
Replacement Spark Plug for etrailer 2,000-Watt Portable Inverter Generator part # 333-312455001
Replacement Spark Plug for etrailer 4,500-Watt Generator and 3,200-Watt Inverter part # 333-330723557
Replacement... view full answer...
You can use the Replacement Remote Control for etrailer 4,500-Watt Generator and 3,200-Watt Inverter # 333-336713641 to replace the remote on your Firman W03083 generator. This unit is also compatible with Firman generators in addition to the etrailer branded units. view full answer...
The Replacement 12V DC Battery Charger for etrailer Portable Inverter Generator # 333-330713634 does appear to be the same charger as the one in your picture that came with your RP12000E CAT portable generator.
It has the same model number, part number, input and output specs. We do not carry the Cat/Caterpillar generators, so I cannot "confirm". But as far as I can tell, this is the same charger you currently have. view full answer...
I spoke with my contact at Lippert and they stated that the second generation of the Ground Control did not have a remote. If yours had a remote you would have the 3.0 generation and the part # LC358601 would be the correct one for it. view full answer...
The A-iPower 2,000-Watt Portable Inverter Generator # 289-SUA2000i you were looking at has an OEM spark plug that is labeled as "Torch E5T".
According to the owner's manual to replace it you need either a NGK BP4H or a Champion L95YC that you'll need to acquire elsewhere.
If you have a different generator then you'll need to refer to the owner's manual for the correct spark plug replacement type. view full answer...
Yes, the Replacement Remote Control # 333-336713641 will work with your Firman W3650ir generator. Your generator must have come with a remote for this to work with it. view full answer...
Since we do not offer Generac generators, I don't have the ability to verify the compatibility of replacement parts, but you are able to determine what will work based off of the capacity and cycle of the solenoid that is currently being used in your generator.
The Pollack Starter Solenoid # PK5230701 has a 12v/100amp capacity and from what I was able to determine with my research, doesn't seem to be the same solenoid that your Generac generator uses.
I would instead recommend checking... view full answer...
I went ahead and checked out your Firman WO3383IR and it turns out unfortunately the receptacle you're referencing is not replaceable.
That said, the only replacement we carry that you're needing as well is the Replacement 12V DC Battery Charger for etrailer Portable Inverter Generator # 333-330713634. view full answer...
I spoke to my contact at Thule about this and found that since you have the older generation Thule Evolution cargo box you would need to get the Replacement QM3 # TH04997 if you need replacement hardware.
You could only go with the EasySnap setup on an Evolution box if it is the second generation of Evolution. view full answer...
We have isolators like the Deka part # DW08771 which was designed for this situation. It will charge both batteries while also keeping them separate which means they wouldn't be in parallel. view full answer...
You would need to use whatever the manufacturer lists as an acceptable spark plug replacement. For the A-iPower 2,000-Watt Portable Inverter Generator # 289-SUA2000i you would need an NGK BP4H or a Champion L95YC, which you should be able to find at your local hardware store. view full answer...
The WVOM43 monitor you have now is the 1st generation system and, as you said, wireless. The # VCMS17B is a wired camera so it is not directly compatible. 1st generation parts are no longer being made, and the newer generation is not backwards compatible either.
I have two options for you. The first is to use the # VCMS17B with the WVRX1AP transmitter. This is not something we carry since the 1st generation is being phased out, but it will allow you to use this camera with your monitor.... view full answer...
The Furrion Vision Wireless RV Backup Camera System FOS48TA-BL is the older generation and will not work with the Furrion Vision S Wireless RV Backup Camera part # FCN48TASF which is the new generation. The only other option would be to upgrade to the new generation, the Furrion Vision S Wireless RV Backup Camera part # FOS43TASF for a 4.3 inch screen or the # FOS05TASF for a 5" screen. If you go with the # FOS05TASF, you can add an additional 3 cameras if you wish.
We do offer just... view full answer...
If you have the old first generation system like I'm thinking you have then you can replace the rear camera with part # VGR84VR. You should have a 4-pin CEC connector on your current camera if this is the case and your monitor would not have the "WiSight 2.0" logo on it. The 1st and 2nd generations of these camera systems are not cross compatible so it's imperative that you choose the correct generation equipment.
The # VGR84VR is the only portion of the 1st generation systems that we... view full answer...
I've confirmed with Extang that the # EX1033 you mentioned is indeed the correct replacement hinge for the panel closest to the tailgate. It is compatible with the first generation Extang Trifecta you have. view full answer...
We have one center hanger available for Dexter 10k axles with 3" wide slipper springs. That is the Center Hanger for 3" Wide Slipper Springs - 4-1/8" Tall - 1-1/8" Bolt # 29-43-2. You will want to measure your current center hanger to ensure it matches the 4-1/8" height of this hanger. view full answer...
The Generac tailpipe 0E0683 that you are looking for has been discontinued, although you may have luck finding an alternative tailpipe with similar specs. It has an inside diameter of 1-1/4" and appears to measure 11-3/4" long according to my research. The closest thing we have is Camco Gen-Turi Replacement 30" EMT 90-Degree Discharge Pipe # CAM44812. The smaller end had ID of 1.37" and OD of 1.5", while the flare end measures 1.53 ID to accept a 1-1/2" pipe. It measures 30" long but could... view full answer...
The correct replacement transfer switch for your PD52 transfer switch in your 2019 Jayco North Point, is the:
- Progressive Dynamics Transfer Switch - Metal Case # PD52.
This transfer switch can automatically reroute your RV's AC input from shore power to generator power, and can also be use with an inverter in place of a generator.
Attached is a review video for you to check out as well. view full answer...
The Furrion Replacement 5" Monitor # FR97FR is going to be specific to the Vision S series of cameras. If you have the older Vision or Vision II you will need to upgrade to the Furrion Vision S Wireless RV Observation Camera System # FCE48TASL-05. Furrion discontinued the older cameras and monitors so there are no generic replacements. view full answer...
Bulb types can often be changed as long as there is a compatible equivalent version and so long as the new type does not cause fit or temperature issues. You could not go from an LED to a halogen since the waste heat generated by halogen bulbs is fairly substantial and far more than what an LED light's housing might tolerate.
The Pilot Bully Bumper Mount Backup Light # PL-807 uses a standard H3 type halogen bulb like # P250003W. We do offer halogen-to-LED upgrade bulb kits from Putco that... view full answer...
Go To Results