It sounds like you're either needing to replace the axle on your trailer or you need a lift kit for them.
To replace the axle the only torsion replacement we have comes from Timbren with their Axle-Less systems. These come in a variety of options but for standard configurations we have the following:
- 5-Bolt Idler Hub # A35RS545
- 5-Bolt Brake Assembly Kit # A35RS545E
Attached is a review video of the Timbren kit as well as a link to our selection for you to filter through. If you... view full answer...
I'm assuming you're speaking of a 5.70-8 tire size, is that correct?
If so, none of he 5.70-8 tires we offer are rated higher than 65 mph. In order to achieve a higher speeding rating, you'd need to switch to a different wheel/tire size.
If you have 5.70-8 tires, I'd recommend measuring to see how much clearance you have to the inside of the tire, between the sidewall and the closest part of the trailer. If this distance is greater than 3-1/2 inches, you can move up to a 215/60-8 wheel/tire... view full answer...
You have a galvanized 1200 lb axle that uses L44649 inner and outer bearings, typically used on PWC trailers, I'd go with # AKIHUB-545-2-LFEZ-2K which is pre greased and ready to install. The hub also includes the dust cap for E-Z lube or standard spindles as well as the lug nuts. The hub has a 5 on 4-1/2 inch bolt pattern which is very common. I'll link to an install video that you might find helpful.. view full answer...
The direct replacement for your Lippert Components model 113407 stabilizer jacks can be found with part # LC369774 on our site. My contact at Lippert confirmed that this is the correct replacement. view full answer...
We have a drop leg for the Lippert trailer jack part # LC285318, it's part # LC405217 which is a 9 inch diameter drop leg. Or we have the part # LC165253 which is just the foot pad.
The # JF-1105H-Z is not a fit for your jack though. view full answer...
The Replacement License Plate Light Kit for Westin Bumpers - Chrome # 00007153 is not a custom fit for your 1999 Nissan Maxima, but it absolutely can work for your application. Another option is to use a trailer license plate light like the LED Trailer License Plate Light with Chrome Housing - Submersible - 2 Diodes - Round - White Lens # LPL11CB or Round Trailer License Plate Light with Mount Ears - Chrome Plated # LP71CB.
We don't have a custom assembly for your license plate light,... view full answer...
The Surco key part # SPN-100-003 is key number 003. This would be the correct key for if you needed that key number. If you needed a different key number you could let me know and I'd be able to pick you out what you'd need. They do not all use the same key so it wouldn't be a master key. view full answer...
It sounds like you're talking about the Velcro strips that keep the cover secure on the sides on your 2010 Nissan Frontier. You can use the Replacement TruXedo TruXport Shur-Bond Hook-And-Loop Fastener Strips for 6-1/2' Beds # TX1117876 and cut it down to size. If you needed the loop side for the tarp then you can use two of the # TX1705183.
If you meant the corner weather seals we have the Replacement Corner Weather Seal for TruXedo TruXport Covers # TX1703568. We also have the rear... view full answer...
We will be glad to help but unfortunately there are all kinds of options and possibilities. The best way to find the right replacement brakes is to find the weight capacity of your axle (see attached picture), the size of your brake mounting flange (4-bolt pattern most common), and your drum diameter for drum brakes and rotor diameter for disc brakes.
If your trailer has a 3,500-lb axle with drum brakes and a 4-bolt brake flange, I recommend something like the Hydraulic Brake Kit,... view full answer...
You could replace a double-eye leaf spring with a slipper spring like the # e33SR spring you'd looked at, but it's recommended that you remove the existing rear hanger (assuming it's a single axle trailer) with a rear hanger like # 115706S as your existing rear hanger isn't designed for use with slipper springs.
You'll also want to choose a spring with sufficient capacity to handle the weight of the boat and trailer. You can choose a higher rated spring than your existing one, but be aware... view full answer...
In order to replace the rear header on your TruXedo Lo Pro Soft Roll-up Tonneau Cover - Black # TX584101 you'll want to use the Replacement Rear Header for TruXedo Lo Pro Soft, Roll-up Tonneau Cover # TX5841-RearHeader.
Unfortunately your cover cannot be upgraded with a dual locking header. view full answer...
While there is an option, there are no longer direct replacement parts for a Sears X-Cargo Sport 20 rooftop cargo box. The only one that can work is from Thule:
- Replacement Lid Lifter Hinge for Thule Cargo Boxes # TH14936
The spring on this strut is going to be stiffer than what was on your cargo box, so please be aware of that, but it is currently the only available option for a replacement. view full answer...
The Replacement Wiring Harness # 27-9903 is a kit that will cover the wiring for both boards. With that being said, I spoke to my contact at Westin and he mentioned that if connection does not appear to be the same as the ones that are currently on your vehicle that this is likely not a Westin # 27-0015-1565 running board which is designed to fit on your 2010 Nissan Titan. He did say that the board you have on your Titan is most likely a factory installed molded lighted running board that... view full answer...
The Curt MV Weight Distribution System w/ Friction Sway Control # C17062 sounds like the lift bracket hook may be needing replaced. That hook should easily hold onto the chain link to lift the bar. For this replacement I recommend the Replacement Lift Bracket for Curt Weight Distribution Systems # C17008. view full answer...
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118670 you asked from will utilize a self tapping screw like # 101131802. This is the #8 x 1/2" screw. view full answer...
I do not know of a way to check a relay and see if it is good other than to use a new relay in the wiring.
For your 2008 Frontier, a wiring harness like part # C56225 uses three relays, so it could be any one of the three has possibly gone bad.
We do offer the Curt Relay kit # C57000. This kit includes the two smaller Blue relays and the larger Brown relay. view full answer...
The modern equivalent of a 7.00-10 tire would be a 205/65-10 tire. We offer this size Loadstar tire in four load ranges: LR B # AM1HP50 for a maximum load of 910 lbs, LR C # AM1HP52 for a load of 1,100 lbs, LR D # AM1HP54 for 1,330 lbs, and LR E # AM1HP56 for 1,650 lbs. This high-quality bias tire provides superior stability and excellent handling at high speeds.
If you are also looking for wheels, we offer a variety of different styles. If you'd like to send me your bolt pattern, I'll... view full answer...
Yes, we do have the replacement control unit for Kwikee series 28 steps.
- Replacement Control Unit for Kwikee Electric RV Steps # LC379146
This is the same control unit that is included in the Kwikee Steps Replacement Kit # LC379769 for 28, 31, 37, and 39 series steps. view full answer...
The most I was able to find about the Coleman 4735CC201 leaf spring is that it's rated for 1,000 lbs which means it goes to a 2,000 lb axle. For that application we have the 4-Leaf Slipper Spring w/ Radius End # e69SR which measures 25-4/8" long from the center of the eye to the end of the spring itself. If you use a jack to raise your trailer by the frame you will be able to get under the trailer to measure the leaf spring without it being compressed and compare that to our length.
Something... view full answer...
To get replacement hardware for the Reese trailer hitch on your 2012 Nissan Xterra you can use the part # RHK. This will give you all of the hardware needed to install the hitch. If you don't want all of the hardware then you should be able to find those at your local hardware store. You'll want to make sure that the bolts are at least grade 5 in regards to strength. view full answer...