Replacement Rear Header for Truxedo LoPro on 2011 Nissan Frontier with 6 Foot Bed

Question

Question:

I looking to replace the rear header on my truxedo lo pro cover Serial # 015687710 as it is worn and will not stay locked. Is this the one and do the latches come with. Is mine upgradeable to the dual locking system currently out. thanks

asked by: Jeffrey V

0

Expert Reply:

In order to replace the rear header on your TruXedo Lo Pro Soft Roll-up Tonneau Cover - Black # TX584101 you'll want to use the Replacement Rear Header for TruXedo Lo Pro Soft, Roll-up Tonneau Cover # TX5841-RearHeader.

Unfortunately your cover cannot be upgraded with a dual locking header.

expert reply by: Erik B

0

Answer 1

Hey Rick, thanks for all of the info you gave us on your Truxedo tonneau. Based on that the correct rear header you'd need is the part #TX5691-RearHeader.

view full answer...

Answer 2

The Replacement Rear Header Assembly for TruXedo Lo Pro Soft Roll-up Tonneau Cover #TX578101-REARHEADER is the correct header assembly for your 2007 Ford F-150 6-1/2 foot bed.

view full answer...

Answer 3

The Voyager WiSight Wireless RV Backup Camera System #ASA37YR you were looking at is only compatible with the RV Backup Camera #ASA74YRor #WVH100 so this would need to be the camera you already have installed or you would need to replace the camera.…

view full answer...

Answer 4

We do have what you need, but since your 2022 Winnebago 2529RG is prewired for the Voyager system you will not want to use the Voyager WiSight 2.0 Wireless RV Backup Camera System w/ Night Vision #ASA57YR that you were looking at. Because you will…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 7

Thanks so much for the photo, it was super helpful, and what it shows is that your trailer has the Voyager WiSight Pre-Wire Plate. This will allow you to mount the Voyager WiSight camera system: - Voyager WiSight Wireless RV Backup Camera System…

view full answer...

Answer 8

There isn't an adapter to connect the wiring of a Furrion camera to a Voyager. With that said you can pretty easily just cut the connectors off and then connect to the camera since it's only two wires.

view full answer...

Answer 9

The reason why you would need the #VGR74VR filter to use the #ASA37YR is because your 2022 GMC Sierra 1500 will have pulse width modulation (PWM). This means it won't send consistent power back to the camera and you're going to lose the…

view full answer...

Answer 10

That's weird, the 7-Way Vehicle Power Adapter for Furrion RV Observation Camera #FR87PR should allow you to use your camper at the same time as that's what it's designed for. If you want to just avoid the adapter all together, I would…

view full answer...

Answer 11

The steps for pairing your Voyager WiSight 2.0 Wireless Backup Camera System #ASA37YR camera and monitor are as follows: 1. Make sure the monitor is connected to 12 Volt DC power supply, but 12 Volt DC power is removed from the camera (clearance…

view full answer...

Answer 12

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Replacement Rear Header for Truxedo LoPro on 2011 Nissan Frontier with 6 Foot Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching