For starters, the vast majority of cargo boxes and replacement mounting hardware for cargo boxes will not work on factory crossbars for a Nissan Xterra as they are very large in comparison to the standard crossbar sizes that these cargo boxes and replacement mounting hardware are designed for.
Unfortunately, I was not able to find any mounting hardware we offer that will work with the Xterra crossbars. I recommend taking a trip to your local hardware store as this will be your best option. view full answer...
You have a galvanized 1200 lb axle that uses L44649 inner and outer bearings, typically used on PWC trailers, I'd go with # AKIHUB-545-2-LFEZ-2K which is pre greased and ready to install. The hub also includes the dust cap for E-Z lube or standard spindles as well as the lug nuts. The hub has a 5 on 4-1/2 inch bolt pattern which is very common. I'll link to an install video that you might find helpful.. view full answer...
If your 2011 Nissan Xterra has the factory tow package with the 4-Way flat connector then you will simply need to use the Hopkins # HM43575 which will plug right into the factory connector. If instead you have a 7-Way connector, like what comes in the T-One Kit # 118266, then you will want to use the Tow Ready # 118267. view full answer...
For your 2009 Nissan Xterra, we don't have the part you are mentioning available as a separate unit. We only have a separate connector socket like # PK11893 if the wiring is still intact.
If the wiring has been damaged you will need to replace the entire wiring kit. I recommend the T-One Vehicle Wiring Harness with 7-Way Trailer Connector # 118266 to replace your damaged unit. view full answer...
To get replacement hardware for the Reese trailer hitch on your 2012 Nissan Xterra you can use the part # RHK. This will give you all of the hardware needed to install the hitch. If you don't want all of the hardware then you should be able to find those at your local hardware store. You'll want to make sure that the bolts are at least grade 5 in regards to strength. view full answer...
We definitely have replacement air bags for your 2015 Nissan Xterra Pro4x, you'll want to use Firestone Rear Air Spring, Tapered Sleeve, 1/4" NPT # F9002. These will be a direct replacement for your Xterra with the Firestone Sport-Rite air springs, they are sold individually, so you'll want to pick up a pair if you need both sides.
When you replace your bags, you may find that you need to repair or replace some air line or fittings. The Air Line Service Kit for Firestone Ride-Rite/Sport-Rite... view full answer...
While I do not have them available for purchase separately the Yakima SnapAround Mounting Brackets part # Y8860081 uses 5/16" carriage bolts and nuts. These can be sourced at your local hardware store. Stainless would be the best option to prevent corrosion or rusting. view full answer...
Unfortunately we do not have the M8 x 100 carriage bolts for your Swagman Kayak Carrier because Swagman does not have that bolt as a replacement product. I reached out to my contact at Swagman to confirm and he recommended the Replacement Knob and Bolt for Wheel Cradle on Swagman Platform Bike Racks # P199 which has a bolt with a slightly larger head but the same threading you need, so he assured me it will work. view full answer...
It sure is; the socket and harness that comes with 7-Way Connector # 118266 are available separately as Replacement for Tow Ready Nissan Vehicle Wiring Harness # 118267. I have added a link to a video review of this part for you to check out. view full answer...
Since you have the round connector for a 7-way already on your 2008 Nissan Xterra you can use the part # 30955 which would plug right into the connector you have and provides a 4-way and a 7-way. view full answer...
We will be glad to help but unfortunately there are all kinds of options and possibilities. The best way to find the right replacement brakes is to find the weight capacity of your axle (see attached picture), the size of your brake mounting flange (4-bolt pattern most common), and your drum diameter for drum brakes and rotor diameter for disc brakes.
If your trailer has a 3,500-lb axle with drum brakes and a 4-bolt brake flange, I recommend something like the Hydraulic Brake Kit,... view full answer...
From your description it sounds like you are looking for the Replacement Double Ball Joint # LC388220, although this is the entire ball joint and not just the bolts. This connects the gear plate to the actuating arm on a Lippert Coach Step or Stromberg Carlson sliding step.
The only other hardware available for a Coach Step is the Replacement Joint Assembly Hardware Kit # LC216567 which is for a joint assembly and includes:
- 5/16"-18 Diameter x 1-1/4" long hex-head shoulder bolt
- 5/16"... view full answer...
In order to find the correct replacement hub for your 1999 Flagstaff Pop Up Camper you are going to need to identify the bearings you have now. You may be able to find the part number stamped into the side of your bearings once you remove and inspect them.
If you are unable to find a part number, you will need to measure. I recommend using a digital caliper like the # PTW80157. You can either measure the inner diameter of your bearings or the spindle where the bearings ride. See the attached... view full answer...
The Tow Ready wiring harness you referenced, Replacement OEM Tow Package Wiring Harness with 4-Flat # 118263, is a correct fit for the 2007 Nissan Xterra that came with the factory tow package.
However, if your OEM vehicle connector is missing you can obtain one from your local dealership or you can go an easier route and simply wire in a 4-pole vehicle connector like # 18002. You can use butt connectors like # 05731-5 to connect the 4 wires, matching them color for color. Once you make... view full answer...
The single leaf spring you referenced, part # e46SR, would work fine as a replacement for the 5-leaf springs you currently have. You are correct in stating that corrosion would be less of an issue with this particular spring.
Make sure to replace the leaf springs in pairs by axle. view full answer...
For replacement mounting hardware for Curt trailer hitch # 13183 you will need # RHK. On the RHK page you will enter the hitch number and then select the manufacturer, Curt, from the drop down menu. The hardware pictured on the RHK page is just a representative photo and is not the actual hardware you would receive. view full answer...
The Curt Trailer Hitch Receiver # 13514 will use 4- M14 bolts with 9/16" lock washers and 2- M12 bolts with 1/2" conical toothed washers.
I recommend the Replacement Hardware Kit for Trailer Hitches # RHK. You will just need to input that you have a Curt hitch item number 13514 when ordering. This will ensure that you get the exact size and grade hardware for your hitch. view full answer...
I have a suggestion for you as the rubber style plug is obsolete when Ram switched to the new Cover # EJ-3520-BCV style which uses the Cap # EJ-3520-BCP you found. With your cover having the odd egg shape you can enlarge the hole to a round hole which you can fit with a rubber firewall plug that you can source from a local auto parts store. Do be sure to verify sizes available before cutting a hole in your current cover. view full answer...
We have exactly what you are needing to replace the hardware for the trailer hitch installed on your 2000 Nissan Xterra.
For a complete replacement hardware kit, you will use part # RHK. Once on the product page, you will simply type the model number of the hitch you have into the Hitch Item Number box and select the manufacturer from the drop-down menu. We will then assemble the correct hardware kit for the trailer hitch. view full answer...
Go To Results