The bracket kit you referred to is compatible with the Westin E-Series Nerf Bars. We do have a bracket kit for the Westin E-Series 3 Inch Nerf Bars for your 2013 Titan, but the 23-299PK bracket kit won't fit your truck.
For the Westin E-Series 3 inch nerf bars, you'd want the # 23-258PK, but keep in mind this bracket kit is only compatible with E-Series 3 inch nerf bars. view full answer...
I believe you are looking for the Replacement Hardware for Reese 16K Fifth Wheel Head Assembly and Head Support # 30583. These bolts mount the head cross assembly to the legs and are only available in the kit. view full answer...
The Replacement Dual Latch Kit for TruXedo TruXport # TX1117755 is the replacement part you're looking for on the TruXedo TruXport Tonneau Cover # TX297201 view full answer...
The Replacement Tarp # TX1497301-CVR is for the TruXedo Pro X15 Soft Tonneau Cover # TX1497301 which fits the 5-1/2' version of your 2018 Nissan Titan. view full answer...
For the Extang Solid Fold part # EX83700 that you have installed on your 2007 Nissan Titan the correct mounting clamps are the part # EX31003005 for the clamps at the rear of the truck bed and part # EX42FJ for the clamp at the front of the truck bed. view full answer...
I was able to pull up your previous order and confirm your mirrors are the K-Source Universal Towing Mirror - Clip On # KS3891. The replacement straps you need are the Replacement Ratcheting Strap for K-Source Universal Towing Mirror - Clip On # KS3891STR. These will be a perfect fit for your mirrors. view full answer...
The correct brake controller install harness for the Tekonsha Voyager part # 39510 you have for a 2012 Nissan Titan is the part # 3050-P.
I attached an install video for this harness on a similar 2015 Nissan Titan as yours for you to check out as well. view full answer...
Thanks for the photos!
Your coupler has pretty generic markings, but from what I can see if looks like you need one of the following parts:
- Breakaway Cable for Model 60 Actuators # T4623800
- Breakaway Cable for Model A-75 and A-84 Actuators # DX76XR
Match this with the style you're needing to replace and you'll be good to go! I believe from your photos you need the kit for model A-75 and A-84 actuators. view full answer...
I have attached all of the replacement parts you are looking for on the TruXedo Lo Pro Soft, Roll-up Tonneau Cover for a 2004 Nissan Titan with 6-1/2 Foot Bed and Utili-Track System.
Replacement Cover part # TX5971-CVR
Replacement TruXedo Shur-Bond Velcro Brand Fastener part # TX1115174 (Cut To Fit)
Replacement Header Seal part # TX1704787
Replacement Safety Strap part # TX1115355
Replacement Tension Control Bracket part # TX1703260 view full answer...
For your 2006 Nissan Titan, we have two hitches that are confirmed to fit. If you have the Curt Trailer Hitch Receiver # 13199 then the installation details show needing 1/2 inch conical toothed washers and bolts that are M12-1/25 x 40 HEX to fit in your existing weld nuts. The Draw-Tite # 41551 will use 1/2 inch lock washers and M12 x 1.25 x 45mm CL8.8 bolts with the existing weld nuts. view full answer...
The direct replacement for your Lippert Components model 113407 stabilizer jacks can be found with part # LC369774 on our site. My contact at Lippert confirmed that this is the correct replacement. view full answer...
It sounds like you're looking for a Curt Brake Controller Wiring Harness. There's a custom adapter, part # C51382 which plugs into the connector under the dash or a universal model, part # C51515 which would plug into the connector on your Curt # C74VV Venturer Brake controller, providing 4 bare wire connections on the end. view full answer...
I spoke to Aries and the Replacement Step Pad for 4" Wide Oval Nerf Bars # AA2090161 will fit your 229006-2 nerf bars. These were replaced by the # # AAS229042-2 in 2016, which do only use 4 posts, so the middle posts will not be there and it will measure a little shorter at 23-5/8 inches long. view full answer...
The Replacement Clamp Assembly # TX1115191 is what you need for your TruXedo Lo Pro Soft Roll-up Tonneau Cover # TX597301 on your 2021 Nissan Titan with the 5-1/2' Bed. view full answer...
When picking out new trailer leaf springs it is important to closely match their length with your existing sets. Leaf springs will definitely stretch/lengthen a bit over time (around an inch or so at most) but the 20-3/8 inch long 3-Leaf Double-Eye Springs # e84SR that you referenced are likely much too short for your current suspension setup. Using these leaf springs would require you to completely change the suspension, including cutting off the current hangers and welding on new ones... view full answer...
The TruXedo Lo Pro QT tonneau cover for your 2006 Nissan Titan king cab without utilitrack is # TX588601. For the replacement tarp only for this cover use # TX5886-CVR. You should not need any other parts.
The cover you referenced, # TX1117651, will not fit since it is the replacement for certain GM trucks. view full answer...
The Replacement Wiring Harness # 27-9903 is a kit that will cover the wiring for both boards. With that being said, I spoke to my contact at Westin and he mentioned that if connection does not appear to be the same as the ones that are currently on your vehicle that this is likely not a Westin # 27-0015-1565 running board which is designed to fit on your 2010 Nissan Titan. He did say that the board you have on your Titan is most likely a factory installed molded lighted running board that... view full answer...
Unfortunately, the replacement tarp you're looking for, for your Extang Trifecta Soft Tonneau Cover # EX44930 (DISCONTINUED) is not available.
As a result, I recommend upgrading to the Extang Trifecta Signature 2.0 Soft Tonneau Cover # EX94930. This tonneau cover is a direct fit for your Titan, and is an excellent upgrade for your old Trifecta cover. view full answer...
It looks like you were looking at the Trailer Idler Hub Assembly # AKIHUB-545-35-EZK which, if your trailer axles have a 3500-lb capacity, are going to be a great choice to replace the hubs on your Bass Tracker Tournament XT trailer. I was able to check your previous order to find the bolt pattern on the wheels you ordered and it looks like you ordered the # AC13R45WSQ, which have a 5 on 4-1/2" bolt pattern- so these hubs match up with the wheels you ordered.
The one thing you'll want... view full answer...