Your 2019 Heartland Cyclone model 4270 5th wheel is going to need the 35" Equalizers # MR39ZR like you found. You can verify this if you like by measuring from the center of the center wheel to the center of the front and rear axles. You will also need the MORryde Suspension Upgrade Kit # MR26ZR. view full answer...
I looked up pictures of your 2021 Heartland Prowler and the taillights it uses are the part # RVSTB60 for the passenger side and # RVSTB61 for the driver side. view full answer...
Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part # BVD0449-A01 that you referenced if you wanted white or the part # BVD0449-A03 for the same smoke color you have now. view full answer...
In order to find the correct replacement for your 2011 Heartland Elkridge you are going to need to identify your current pin box. Typically there is a sticker located on the pin box or king pin with the pin box number. If you are unable to find the sticker then you may be able to contact the manufacturer with the VIN to see what pin box it has. If all else fails, you will need to measure the bolt pattern. See the attached article for how to measure the bolt pattern and identify your pin... view full answer...
We do have what you need, but the Vista Light LED Kit for Solera RV Awning # LC25VR is designed to add lighting to your Solera awning. Since you already have lighting on your awning you would want the Replacement LED Light Strip for Solera RV Awning # LC423331.
The Replacement LED Light Strip for Solera RV Awning # LC423331 is 20' long but can be cut down to size. It installs by sliding into the track that is already in place from your current light kit. The Replacement LED Light Strip... view full answer...
Realistically there would be no reason or advantage to switch from a 205/75-14 tire to a 215/75-14 tire, although the 215/75-14 will fit your current wheel. If you are looking for a radial tire, you could get a radial tire that is the same size you have now like the Karrier ST205/75R14 Radial Trailer Tire - Load Range D # AM10235.
This tire will have the same/similar outer diameter and section width of your current tire. The difference is minimal between the 205/75-14 and 215/75-14, but... view full answer...
If you're just needing the handle part of your waste valve then you should be able to use either the Replacement Handle for LaSalle Bristol Cable-Actuated RV Waste Valves # 34490CMA1G which uses a screw to install, or the Replacement Handle for Bladex and Valterra Waste Valves # T1003-6MNVP which threads onto the waste valve. If you aren't sure what you have just send me some photos and I can try to help you out.
Since these handles use threads to install you shouldn't have any problems... view full answer...
Yes, if you currently have the CRE2-33 MOR Ryde CRE3000 Trailer Suspension Equalizers # MR87ZR installed, you can replace with the Road Armor Shock Absorbing Equalizer Kit, # LC696740. There is a slight difference in the distances, but they are interchangeable. view full answer...
Yes, you can remove the rivets and use some self tapping screws to secure the # LCV000334398 and complete the installation. If you watch the video attached below starting at the 10 minute mark you will see where they used the # FA1131822 to finish installing the replacement fabric. view full answer...
You'll want to first verify the brand of the awning to ensure you actually have a Solera before purchasing anything. If you look at the base of the awning arms it will typically either say Solera (Lippert) or A&E (Dometic). If you have an A&E awning you would need to reach out to Dometic directly for replacements. For Solera we have the following replacement shocks depending on the size/type of the arms:
For short or flat support awning arms you'll need part # LC280343 (measures 26" extended/15"... view full answer...
Your best option is to measure the horizontal distance between the holes of the equalizers you have on the trailer currently and pick the EquaFlex that matches that dimension. The part # LC281314 has this distance at 5-1/2 inches (see first picture), and the # LC279689 has this distance at 7-1/2 inches (second picture). Going with the kit that has the closest dimensions to what you currently have will be your best option. view full answer...
In order to determine the correct replacement control panel for your 2015 Heartland Bighorn 5th Wheel, you will just need to identify if your system is hydraulic or electric, and if the system is electric, are the front and rear jack legs are square, or if the rear jack legs are round.
If all jack legs are square, then you have the Lippert Ground Control 2.0, and the correct replacement touchpad is the:
-Replacement Auto Level Control Panel for Lippert Ground Control Leveling System ... view full answer...
The Replacement 6-Point Controller for Lippert Components Ground Control 2.0 Electric Leveling System # LC56VR is the correct replacement for your 276452 controller. There are a few other controllers out there but they are for different models like the 3.0 system or 4 point instead of 6 point.
In order to be sure everything works as it should you will need to replace your 276452 controller with the Replacement 6-Point Controller for Lippert Components Ground Control 2.0 Electric Leveling... view full answer...
The dimensions of your Sylvania Microwave SR-11092B are 12-1/4" tall x 20" wide x 13" deep which the Greystone Microwave part # 324-000105 would be an excellent fit as a replacement since it measures 12" tall x 19" wide x 14-5/8" deep.
The Furrion microwave part # FMSN09BL has similar dimensions too at 19-1/16" long x 13-5/8" wide x 15-7/8" deep. view full answer...
I have a solution for you, but the FOC48TA-8L is an older model of the Furrion Observation system and has since been discontinued. These cameras are not compatible with the newer monitors like the # FR77FR you were looking at, so you would need to replace the entire system.
You can use the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 4.3" Screen # FOS43TASF to replace the camera and give you a new monitor for the observation system using the existing... view full answer...
From what I was able to find, the 2013 Heartland Gateway 3200RS has a GVWR of 14000-lbs, so it would be most likely that the trailer has 5200-lbs or 7000-lbs axles; this size axle would have hubs that accept 12" brakes, so you're likely correct. If you can confirm that your axles have that capacity then they will take 12" brake assemblies.
To replace those old brakes I recommend using the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies - 5.2K to 7K #... view full answer...
The Replacement Short Arm Assembly # LC404523 is the correct replacement assembly to replace your damaged awing arm on your Solera Awing. view full answer...
Thank you for the photos and measurement!
We have a variety of slide out wiper seals that might work for your application but you'll want to look underneath/behind the seals you have pictured to make sure they don't have any other kind of design as well since that can change from slide out to slide out.
If you do indeed have a flat wiper seal then what we have that is closest to your seal is the 3" seal from Steele Rubber. Part # SR29FR gets you a 15' strip while part # SR56FR gets you... view full answer...
Sure thing, and thanks for the pictures!
For your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set # LC675817 you're going to want the:
-Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System # LC421484 for a replacement control panel.
This control panel is going to use the same 4-wire configuration that your current touchpad has, is a direct replacement for your unit, and also does not include... view full answer...
Go To Results