The # C89FR has the manufacturer's part number 56436, which is the CURT T-Connector Vehicle Wiring Harness with 4 Pole Trailer Connector. This harness is a confirmed fit on your 2020 Ford Edge as long as you have either the SE or SEL trim package.
I've also linked the installation video of this part for you to check out, as well. view full answer...
According to what I've read in the owner's manual, your Edge can indeed be flat towed if the specific procedures listed in the manual are followed precisely.
To flat tow your Edge, hook up to the motorhome then press and hold the brake to the floor. Start the vehicle and shift into Neutral with the brake pedal still pressed then turn off the vehicle. On a keyless start equipped vehicle, push the keyless start button one to shut off. If the vehicle has an ignition key, turn the vehicle... view full answer...
According to page 210 in the online version of the owner's manual for your 2007 Ford Edge the AWD version can be flat towed. You will want to refer to your copy of the owner's manual to confirm this and any other specific instructions when it comes to flat towing your vehicle.
A complete flat towing setup consists of a base plate kit, tow bar, safety cables, vehicle wiring, a supplemental braking system, and sometimes a high-low adapter. If you don't already have this equipment then I... view full answer...
Let's start with your Jayco Pop Up Camper.
To add electric brakes, you will need to have hub-and-drum assemblies already installed. If you just have idler hubs like the Dexter # 8-258-50UC1-EZ, you will need to install hub-and-drum assemblies that are compatible with the trailer spindles. The numbers stamped into your trailer's existing bearings and seals will help you determine the proper hub-and-drum assembly. You will also want to make sure you choose an assembly with the same bolt... view full answer...
To order the complete hardware kit for the Draw-Tite trailer hitch receiver, part # 75234, all you need to do is order part # RHK and enter the hitches part number and select "Draw-Tite" from the drop down menu.
This will include all of the original hardware: Bolts, nuts, washers, spacers, and even the bolt leader wire thingy. view full answer...
When it comes to installing a trailer hitch on your 2022 Ford Edge I recommend The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 inch # C78KR.
This hitch has a concealed cross tube so you will only see the hitch head after installation. The hitch has a gloss black powder coat finish over a protective base coat which offers superior rust resistance. The trailer hitch has a simple bolt on installation with no welding required.
For the wiring harness The T-One Vehicle Wiring... view full answer...
I recommend using the Rhino Rack Roof Rack that uses parts # RRVA137B-2, # RRRLKHD and # DK228 because Rhino Rack is a really durable and high quality rack at a bit better price point than some of the other racks available. This is an all black roof rack kit that will allow you to mount a variety of accessories that attach via clamps or the T-channel mounting slots, so you'll be able to put cargo boxes, bike racks, or even a Pioneer Platform like the # RR42114BF.
I've linked a review video... view full answer...
Your 2015 Ford Edge with factory tow package 4-pole wiring does NOT have an integrated trailer brake controller. If it had a controller it would already have a 7-way trailer socket rather than the 4-pole. And you are correct that the 2015 Edge is the first year of the second generation of this vehicle so it is indeed different from earlier years.
Brake controller installation on your 2015 Edge will be a hard-wired type requiring installation kit # ETBC7 along with the controller, such... view full answer...
The Thule SUP carrier I recommend for your 2 boards is their SUP Taxi XT # TH810001. This 2-board carrier includes locks and it fits on almost any shape of roof rack bar. You can see more on this SUP carrier in the linked video.
You will need a roof rack for the SUP Taxi XT and I refer you to the linked page for roof racks that fit your 2008 Ford Edge that has a bare roof.
For a square bar rack you can use the Rhino-Rack aero bar system made of parts # RRVA137B-2, # RRRLKVA, and # DK228.
An... view full answer...
Since you already have the Roadmaster Falcon or Falcon 2 Tow Bar item # RM-520 or item # RM-522 I recommend the Roadmaster Direct-Connect Base Plate Kit item # RM-524444-5. This is the best option for your 2017 Ford Edge 3.5L V6 - without Adaptive Cruise Control because it has the removable arms and will connect easily to the Falcon tow bars. They also have the built in connections for the safety chains. I have attached a couple of pictures below so you can see what this base plate kit... view full answer...
Yes. According to the owners manual of the 2014 Ford Edge, you can flat tow your 2014 Ford Edge with all 4 wheels on the ground. In order to flat tow your Ford Edge you will need 5 main parts. Those parts being a base plate kit, tow bar, safety cables, tow bar wiring and a supplemental braking system. I have included these parts below, along with a brief description of their purpose.
Base Plate Kit: This is a custom fit part for your 2014 Ford Edge and provides the attachment points for... view full answer...
We can help you with selecting and installing a trailer brake controller in your 2014 Ford Edge SEL with factory tow package. Since you already have a working 4-pole trailer connector you will just need the controller itself plus the # ETBC7 installation kit you referenced. Your 4-pole will plug right in to the 7-way included in the installation kit and establish the ground.
I recommend the Prodigy P2 proportional brake controller # 90885 from Tekonsha. This is among the most reliable... view full answer...
A great solution for the bow and stern tie-downs on your 2015 Ford Edge are Malone Hood Loops # MPG308. You just close them under the hood and trunk of your Edge and then connect them to the canoe.
You mentioned a Yakima roof rack. If your Edge has a naked roof with no factory rails the parts needed for a Yakima rack are:
50 inch JetStream Cross Bars # Y00425
BaseLine Towers # Y28TR
Fit Kit # Y06102 and # Y06139
Then you can add the Yakima KeelOver # Y04069 to carry the canoe on the... view full answer...
For your 2013 Ford Edge we have 2 different options for a base plate kit.
One is the Roadmaster XL # 4408-1 and the other is from Blue Ox # BX2628. The both are compatible with the non-EcoBoost without Adaptive Cruise Control. The difference between these options is that they install slightly different and the removable draw bars have a different design.
The Roadmaster XL # 4408-1 will work great with the Roadmaster Falcon 2 Tow Bar # RM-520 and 6K Coild Safety Cables # RM-643. If you... view full answer...
If you only have a 4-Way on your 2015 Ford Edge SEL, like the Curt # C56272 or Tekonsha # 118669, then the wiring that you need is the Kit # ETBC7. This connects to your 4-Way and provides both 4-Way and 7-Way connectors that are fully functioning.
You will need a brake controller to send a signal back to the brakes on your boat trailer. We actually have an installation video of the ETBC7 kit and the popular Prodigy P3 # 90195 brake controller being installed on a 2016 Ford Edge that you... view full answer...
We don't have the exact spacer block that would've been included with the # C13067 hitch but the # RP3022 comes very close. The block is a little narrower, and the hole is centered rather than being on one end. This means that the block may try to spin once the bolt is being tightened. If this happens, use an impact wrench. The impact wrench will spin fast enough to prevent the block from spinning. It might take a minute or so, but the bolt will tighten. You'd also need a few bolt leaders,... view full answer...
We carry several lighting options for the 2013 Ford Edge. I have included a link to them for you to view. A brake light relay may be required depending on the system you choose. A kit that bypasses the vehicle wiring like a magnetic kit # RM-2120 will not require a brake light relay. Any other system will require the brake light relay # RM-88400.
You will also want to consult the vehicle owners manual for additional information on flat towing the vehicle. In the research I did I found... view full answer...
If your motorhome is too high for your 2017 Ford Edge, you're going to need to use a high-low adapter like the Roadmaster High-Low Adapter for Tow Bars # RM-076.
This is designed specifically to make up for the height difference between your RV and your towed vehicle. This particular adapter has 6" of rise, and 6" of drop.
I have attached a FAQ detailing how you can measure the correct rise and drop you need for your 2017 Ford Edge. view full answer...
To install a Curt # C51180 Edge brake controller on your 2019 Ford Edge, you'd first need to install a 4 pole trailer wiring harness using part # 118805. Then to install the Edge, you'd use our # ETBC7L brake controller install kit which includes the 4 pole to 7-way adapter and the wire and circuit breaker necessary to make the power feed connection to the battery.
I've linked to some installation and product demonstration videos that will assist you in the install process. The install... view full answer...
According to my research of your Rhino-Rack part number 1375, I think you are most likely referring to the Rhino-Rack Heavy Duty Crossbars -54" Long # RB1375B-2 (black) or # RB1375 (silver) which are confirmed to fit a bare-roof 2012 Ford Edge.
If this is what you have, you need the Rhino-Rack 2500 Series Legs # RRRLKHD and the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Naked Roof # DK228. With both of these components, you will have a full roof rack system on your... view full answer...
Go To Results