None of the 2011 Ford Ranger models came equipped with a factory brake controller port located under the dash. To install a brake controller on your 2011 Ford Ranger Canadian Spec, you would need to use the Brake Controller 7 and 4 way Installation Kit, part # ETBC7.
I have linked a video installation of a brake controller being installed on a 2006 Ford Ranger, which also uses the Brake Controller 7 and 4 way Installation Kit, part # ETBC7. Also linked are FAQ articles on brake controllers... view full answer...
You're correct that the Roadmaster Invisibrake # RM-8700 is not a true proportional supplemental braking system; it's considered a "progressive" system, meaning that when braking is called for, InvisiBrake immediately engages the brake pedal and rapidly ramps up the braking the setting you have selected. I have a solution for what you're looking for in a supplemental braking system, but all supplemental braking systems will require additional tow bar wiring to control the turn, brake and... view full answer...
You shouldn't have any problems getting the install bolts of your 2019 Ford Ranger to break free so that you can install the etrailer hitch # e63ZR. One trick I personally have used is to spray the bolts with WD40 or other penetrating oil about a week before you plan to do the install and by the time you go to install the hitch the bolts will be easy to work with. We do not have specific installers we've worked with in your area but typically it's best to find someone with a solid reputation... view full answer...
The spare tire will need to be lowered to install the Curt Trailer Hitch Receiver part # C13417 on a 2019 Ford Ranger. I understand the instructions do not state this is needed but we have found that this step is required to install a trailer hitch on a Ford Ranger. That said, the spare tire will install right back up into place once the hitch is in position so there should be no worries here. In order to lower the spare tire, there should be a tool somewhere in the vehicle which you can... view full answer...
You are correct that when wiring the Brake Buddy Stealth Supplemental Braking System # HM39530, the red wire from the vacuum pump and the black wire from the battery maintainer will connect to the same wire on the all-in-one connector. But this does not impact the performance of the battery maintainer/charger.
The vacuum pump wire and battery maintainer wire are both drawing power from that one wire on the all-in-one connector, but they are not intertwined in the sense that that battery... view full answer...
The wiring harness you will need to access to install the Pop & Lock Custom Tailgate Lock part # PAL8200 on your 2009 Ford Ranger will be under the passenger's side kick panel. Once the kick panel is removed you will need to test each of the wires with a circuit tester like part # ALL640595 in order to determine the correct functions.
I spoke to my contact at Pop & Lock and they informed me that the green wire on the Pop & Lock is for the lock function which could be either a gray/brown... view full answer...
The Redarc Tow-Pro Elite proportional trailer brake controller item # RED44FR is connected directly to your 2011 Ford Ranger 4x4 through a wiring harness. This harness comes with the brake controller and connects behind the dash by wiring into your truck. The Redarc brake controller activates trailer brakes in proportion to your vehicle's braking action by automatically adjusting your trailer's braking based on deceleration of your Ranger. The brakes also activate immediately which eliminates... view full answer...
Yes, the relay that comes with the Battery Charge Line Kit # RM-156-25 is designed to protect against any voltage from your 2021 Ford Ranger backfeeding to your motorhome.
The Demco Stay-IN-Play DUO # DM86VR is an excellent system for flat towing. It's easy to setup (after the initial installation) and it stays out of the way when you're normally driving your Ranger.
I've linked installation videos of both kits on a 2021 Ford Ranger for you to check out.
For a complete flat towing setup... view full answer...
The roof rack bar in the Darby Extend-A-Truck Kayak Carrier # DTA944-968-924 secures to the roof using a strap that runs through the interior of the vehicle. It is a great quick and temporary way to add a crossbar to the roof of your 2002 Ford Ranger. I have linked a video review of this product for you. view full answer...
Yes, the advantage is that you will get a better ground connection with an independent ground wire on a trailer wiring harness such as # 40215 for your 1997 Ford Ranger. Some converter boxes require a separate ground wire because the factory ground for the vehicle tail lights is not sufficient for the converter's needs. view full answer...
The Viking Solutions Rack Jack Magnum Hoist # 310-VMH001 can be completely broken down for storage and will not take up very much space. This will not be an issue with your Deck system and I did include a picture of the part as it will come to you. The winch can be left on the upright though, so you will not have to do a full rebuild every time you need to use it. view full answer...
The Breakaway Kit with Premium Integrated Charger # 50-85-313 should not overcharge the battery in the system. It will go into a maintenance mode to maintain the optimum charge after the battery is fully charged.
A battery being charged will get hot depending on how much it needs to be charged. It is best to charge the battery while towing or while the vehicle is running so the maximum amperage is being pushed back. This will reduce the time it takes to charge the battery.
Charging even... view full answer...
The install of the Bargman Trailer Tail Light # 30-92-002 does not require a mounting bracket. To install this you would remove the lens of it and then attach the back bracket directly to the rear of the camper and then from there you'd be able to install the lens back on to it and you'd be ready to go. view full answer...
I went outside and tested the Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights, # CR-600LED. It does have turn signal functions (the whole strip blinks when either turn signal is engaged), brake signal functions, and running light functions, so no adapter is needed. view full answer...
I would first start by testing the wires on the T-connector with a circuit tester like the Quickee, # 3808, to make sure that each is functioning as it should. If there is an issue with any of the wires, you will need to replace the T-One Vehicle Wiring Harness, # 118325.
If all functions are working, you can use the Taillight Converter, # C56175, to complete your wiring harness. The wires on this converter will just need to be connect to the wires on the T-connector, color for color. view full answer...
To give you the short answer- No. The crossbar style base plates like the Roadmaster # RM-524459-4 will not interfere with the collision avoidance sensors when installed on your 2019 Ford Ranger. The sensors are mounted on the front bumper far enough away from the base plates that they won't activate them. You will have to disconnect the sensors during the installation, since the bumper is removed, but they are plugged back in once the bumper goes back on. The arms on these base plates... view full answer...
It certainly does sound like a short on the trailer that caused some problems, but I would not rule out the possibility that it is just coincidence and that there is an issue with all the vehicles in some way, shape, or form. If the trailer draws more that 2.1 amps per side for turn/brake lights then that would cause the converter to blow.
On the trailer, make sure its connector is free of corrosion. Then you will want to trace the wiring leading back from the 4-Way to determine if there... view full answer...
You can use the 1/4" Air Line Hose - SMI Air Force One or Stay-In-Play Duo Supplemental Braking System # DM16114 sold in 1 foot increments, so if you need 6 feet of new hose you can simply select quantity 6 on that product page and you will receive one 6 foot section of hose.
The compression fittings like the Replacement Female Push-On Hose Connector for SMI Air Force One Supplemental Braking System # SM99726, the Replacement 1/4" Female Pushlock Fitting for SMI Supplemental Braking... view full answer...
Look at the connector that attaches directly to the light assembly. I attached a picture that shows what the connector will look like that you would need to use. view full answer...
The VueSMART RV and Trailer Backup Camera part # HM34FR is very customizable, it can be adapted to fit any application. I have attached a photo which shows a simple modification that can be made to change the style of mounting bracket. The camera can then be rotated inside said mounting bracket.
That said, I wouldn't be able to offer any advice for a specific application as this will really be up to the installer to determine compatibility. The license plate light circuit however I can... view full answer...
Go To Results