The Trailer Valet Trailer Jack # STC-V211 that you referenced has a 500 lb tongue weight rating.
Check out the review video I attached for more information. view full answer...
Basically, all of the hitches for the 2002 Suzuki Vitara will have the receiver directly below the rear fascia on the vehicle. The Class I hitches like # 60942 will have a little more ground clearance because the receiver is smaller. However you will be very limited in accessories and towing capacity with Class I hitches.
I have included a diagram that shows the position of the Class III Draw-Tite hitch # 41537 relative to the rear fascia. Since the outside of a Class III receiver is 2-1/2... view full answer...
You will want to measure the distance from the center of your hitch pin hole to the edge of your spare tire; the folding cargo carrier we have with the longest distance from the center of the hitch pin hole to the closest edge of the carrier when folded up is the 24x60 etrailer Cargo Carrier for 2" Hitches - Steel - Tilting - Folding - 500 lbs # e98874. This carrier has 9-1/2" from the center of the hitch pin hole to the closest edge of the carrier when folded up, so it would likely be... view full answer...
The threaded pitch of trailer hub wheel stud # RG03-060 is 20 threads per inch and the diameter is 1/2-inch. See diagram to the right. view full answer...
When adding an extension to your receiver, the towing capacity of your hitch is reduced by 50 per cent. If you have a class lll hitch installed on your vehicle, the tongue capacity is 350 lbs. Adding an extension would reduce that number to 175 lbs. Based on the weight of your power chair, your hitch would not be able to handle the weight. I researched your 2006 Suzuki XL-7, and found that the tongue weight capacity is 300 lbs. This would be the weight of the cargo carrier and the cargo... view full answer...
From what I was able to find the towing capacity of the 2007 Suzuki Grand Vitara is 3,000 pounds when properly equipped. Consult the vehicle owner's manual to confirm.
The specs on the 2016 R POD 179 list a dry (unloaded) weight of 2,630 pounds with a gross capacity of 3,785 pounds. So provided you stayed under the 3,000 pound capacity of the vehicle (assuming that your specific model is rated that high) you could tow the R POD. However you will be near the max capacity of the vehicle,... view full answer...
In order to add a 7 way connector to your 2009 Suzuki Equator, you can simply use the # ETBC7, which will utilize your existing 4 way. You won't need to replace the existing harness, but once you plug it in to the ETBC7 you'll need to run a wire to your battery to supply 12v power and one to your brake controller to complete all of the circuits on the 7 way connector. I've linked a basic installation video of this connector that you can use as a guide.
When it comes to the towing capacity... view full answer...
I reached out to my contact at RoadMaster and the RoadMaster BrakeMaster Custom Seat Adapter, # RM-88277, for your 2013 Suzuki Grand Vitara is 3 lbs. view full answer...
The Hopkins wiring harness item # HM43575 has a length of 45-1/4 inches for the wiring alone and the overall length including the plugs/adapters end to end is 48-1/8 inches. view full answer...
Yes, it will so long as you have the hatchback model. The Draw-Tite Hitch item # 24817 is confirmed to fit the 2011 Suzuki SX4 hatchback. It looks like the crossover model is consider a hatchback.
If your Suzuki is a sedan you would need the Curt Hitch item # C11446.
If you are planning on towing you will also need a wiring harness item # 56002 and the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2 inch ball or item # 19256 for a 1-7/8 inch ball. view full answer...
If you have a 2008 Suzuki SX4 Sport model, then the CURT Trailer Hitch, # C11446, will fit and you should not have any problems towing the watercraft provided you stay within the capacities of the hitch. This hitch is rated for 200 pounds tongue weight and 2,000 pounds gross trailer weight. I have included a link to the installation details for you.
You would also need ball mount # C45521 and a ball, # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter) depending on which size the... view full answer...
The best way to transport bikes on your 2010 Suzuki Grand Vitara is to install a trailer hitch like Curt Class III hitch # C13001 and to then use a hitch-mount bike carrier. The advantages of using a hitch-mount rack are higher overall bike/weight capacity than any spare-tire-mounted rack, the ability to use the hitch for other items such as a cargo carrier # C18151 or for towing, and that your bike rack's and bikes' combined weight is carried by the vehicle's frame - it's strongest part.
If... view full answer...
If you are looking at the balls that come in the etrailer ball mount kit # 989900, ball # 19247, is coarse threaded and has a 1-1/2 inch nut and lock washer included. Ball # 19260 is also coarse threaded and it also comes with a nut and lock washer.
The shank diameter on each of these balls is 1 inch which is what the included ball mounts in # 989900 accept. view full answer...
The Thule Canyon XT Roof Cargo Basket # TH859XT referenced in your question weighs 29 pounds. It has a weight capacity of 150 pounds and measures 49 inches long, 40 inches wide, and 6 inches tall. view full answer...
I reached out to the manufacturer and the Putco Tailgate Cap - Stainless Steel # P51614P measures 50.25 inches long. He didn't have a width and we don't have one to measure ourselves so all I can give you is that he says it will cover the top side completely.
This Product Fits The Following Vehicles:
1988 - 2000 Chevrolet C/K Series Pickup 6-1/2 Foot Bed - Stepside
1988 - 2000 GMC C/K Series Pickup 6-1/2 Foot Bed - Stepside
1988 - 2000 GMC C/K Series Pickup 8 Foot Bed view full answer...
I went out to the warehouse to measure Curt trailer hitch # 11128 for you and your 1991 Suzuki Sidekick. The overall length is 34-3/8 inches. The mounting holes are spaced 32 inches apart on center side to side and 4-1/8 inches apart on center front to back. I have included a picture showing these measurements for you. view full answer...
The Fulton Replacement Cable Keeper Kit # F501120 works with 1/4-inch diameter winch cables, or wire ropes. The hole in the keeper matches this dimension, which is shown in the linked photo. This works with cables like # DL24104 which is 50-feet long. view full answer...
I went to our warehouse and pulled a Yakima FrontLoader Wheel Mount Bike Carrier, part # Y02103 to get the measurement you asked about.
I have attached a photo of the front mount that has the width noted. It is 7 inches wide outside edge to outside edge. This will attach to most round, square or factory crossbars. When using this carrier the front wheel does not have to be removed. This carrier will hold one bike with wheels from 20 to 29 inches. it will not work with recumbent or tandem... view full answer...