I have a solution for you, but the Electric Winch # 2953AT is designed to work off of DC power, so it's not something you could plug into a wall outlet to work and it would require a 12v DC power source. Instead, you can use the Dutton-Lainson StrongArm Electric Winch, AC Powered - 2,700 lbs # DL24872 which comes equipped with a plug that will allow you to plug it into an AC power source. view full answer...
I do have an option for you but we only offer the Clazzio Custom Seat Covers in sets, front + middle or front + middle + rear. I have attached a list of these options for you that vary by features such as under seat storage and rear row cup holders.
If you are only looking to cover the front two seats then the best option we have is the Covercraft Work Truck SeatSaver Custom Seat Covers part # SS2372PCCT for bucket or part # SS3374PCCT for 40/20/40 bench. These both come in a light gray color. view full answer...
For what you are looking for we have the Husky Liners cargo mat part # HL28251 which fits from behind the second row seats to the back of the vehicle and fits under the third row. Or for something that fits from behind the third row to the rear of the vehicle we have the # WT11AVMCB. view full answer...
Porpoising (bouncing like you described) and sway are both commonly caused by the same thing when towing and that is not enough tongue weight for the trailer relative to the total amount of weight the trailer weighs. You need the tongue weight to be between 10 and 15 percent of the total trailer weight for the porpoising to stop.
Suspension enhancement would actually cause the bounce to be more severe so I would not recommend going that route. I'd get the tongue weight checked and also... view full answer...
The Round Tube Stainless Steel Trailer Hitch Receiver Step # CR-600 is designed to fit in 2 inch trailer hitch receiver openings which is the size that is available for your 2004 GMC Yukon. So if the Yukon has a hitch then it will be a 2 inch and the step will fit.
If the Yukon does not have a hitch you would need to install one such as # e26KR.
We do have other step options including # BBS-1102 in black as well as # CR-600LED and # BBS-1104L which have LED lights in then. The lighted... view full answer...
The Yakima Q tower roof rack systems have been discontinued by the manufacturer for a more updated option. There are limited options for the naked roof on your Yukon, so I recommend the SeaSucker Monkey Bars Roof Rack - Vacuum Cup Mount - 48" Long - Black # 298-SX6000B. This rack uses vaccum cups (each rated for 210 lbs pull strength) and a round bar. This is a very easy to install and remove system that will suit your vehicle well.
If you need to secure something to your vehicle when... view full answer...
Yes, the Superchips Flashpaq F5 Performance Tuner part # SU2845 which is a fit for your 2007 GMC Yukon with the 5.3L V8 engine will allow you to disable the active fuel management (AFM) or otherwise known as displacement on demand (DOD) if equipped. This device will also allow you to monitor several other engine/vehicle parameters as well as read/clear diagnostic trouble codes (DTC's). The Superchips Flashpaq F5 Performance Tuner can also provide your Yukon with increases in horsepower... view full answer...
The etrailer jack part # EJ-3520-BBX has a height of 20-1/2 inches from the mounting bracket to the top of the jack. Which from everything I looked up appears to be the shortest overall height from bracket to top of jack. view full answer...
If you are talking about Curt hitch # 31302, the instructions do not mention drilling at all. And the first step says that models with tow hooks must remove the factory bolt from the underside of the frame at the forward attachment point. I have linked the instructions to the right for reference. view full answer...
The Reese Pole-Tongue Adapter for Weight Distribution Systems - 7,500 lbs GTW, 750 lbs TW # RP3280 will work well with the Curt MV Weight Distribution System - Round Bar - 6,000 lbs GTW, 600 lbs TW # C17050. You will just need to add a hitch ball like # 40038 for a 2 inch diameter or # C40030 for a 2-5/16 inch option.
If your trailer is aluminum, you will want to check with the manufacturer before using a weight distribution system. view full answer...
You've got a couple of great options for the 2015 GMC Yukon in terms of rooftop storage.
Prior to purchasing any rooftop solution, you'll want to verify your vehicle's roof capacity. This capacity will include the cargo solution itself (Be it a bag, box, or basket) and anything loaded inside of that solution. You can verify this capacity with your owner's manual or vehicle manufacturer.
If you're looking for something straightforward and don't plan on carrying anything else on your... view full answer...
Travel trailers are big lumbering things that offer a lot of surface area for wind to push it around. Using a weight distribution with sway control is going to help tremendously with sway problem you are having. To choose a system you will need to go by the total tongue weight.
Total tongue weight is calculated by taking the tongue weight of the trailer when loaded and ready to tow and adding to that the weight of anything loaded behind the rear axle of the tow vehicle. Based on the dry... view full answer...
While the Yakima Railgrab system is no longer around I was able to find that back when they did offer it and it was a fit for your 2013 GMC Yukon they recommended the small claw which we still offer as a replacement part # Y80145. view full answer...
Going with a bottle jack like the Powerbuilt Unijack Bottle Jack with Built-In Jack Stand # ALL620471 would be what I would recommend. Since it doubles as a jack stand it gives you the ability to jack up the trailer and safely hold it at the height you want when changing the tire. view full answer...
The Hopkins 6-Pole to 7-Pole Trailer Wiring Adapter # 47435 will definitely work as an adapter, but you will indeed have no reverse lights. I do also need to mention that the 6 Round style plug is not going to be a very common style so it may not be a bad idea to upgrade it to a standard 7 Blade.
The Hopkins 7-Pole and 4-Pole Trailer Connector Sockets w/ Mounting Bracket and Wiring # HM40975-11998 will require some cutting and splicing to get installed, but will match the 7 Blade on your... view full answer...
You will first need to determine why The Curt Triflex Controller # C24VV is not working. You will need to check the correct fuse that corresponds to the brake control and its power supply.
In the under hood fuse block (located near battery) fuse 36 is what you need to check.
After checking if the trailer brake fuse is intact, you should then acquire a hook probe circuit tester # PTW2993. When the vehicle is on you will want to test the power wire (black) running into the controller.... view full answer...
A trailer that is equipped with an electric-over-hydraulic brake actuator such as the Titan BrakeRite EHB # T4813102 shown in your photos requires that the tow vehicle have a brake controller installed. The brake controller sends braking signals from the tow vehicle to the actuator on the trailer through the 7-way trailer connector. For reference the instructions for the BrakeRite are included. You need to choose a controller that is compatible with an EOH actuator.
Many vehicles with... view full answer...
The Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair) # BB1980A-SS does not have threads on the hub end of the bearing buddy, it is smooth. I have a video attached that will show an up close view of these products. view full answer...
Yes. The Tuson DirecLink Base Model Trailer Brake Controller - 1 to 4 Axles - Proportional # 335DL-100 controller can be disconnected when not in use, and stored in your glovebox or wherever is convenient! view full answer...
Go To Results