Expert Answers about Nissan Xterra
- Does RoadActive Suspension For 2008 Nissan Xterra Need to be Adjusted When Not Towing
- Nope, you will not need to adjust the tension either before or after towing of the RoadActive kit that fits your 2008 Nissan Xterra, which is the following part number:
- RoadActive Suspension Custom Leaf Spring Enhancement Kit # RAS4529-XT
The # RAS4529-XT is designed not to affect the unloaded ride of your Xterra, and can even improve it because the kit is designed to work with your current suspension. It is an active system, meaning it works when needed; so if you go over a pot hole...
view full answer... - Infamous Black/Blue Wiring Mixup On The 2005-2013 Nissan Xterras
- Chances are that if the brake controller is reading the trailer while connected, then it is not a blue/black wire mix-up. To test this, you will need to use a circuit tester like part # PTW2993 and probe the 5 o'clock position on the rear of the 7-way. If the power is constantly hot, the wires are switched. If the 5-o'clock position is only hot while the manual override is activated, the wires are not switched.
If the wires are switched, you have two options. The first option would be...
view full answer... - Installation of Trailer Wiring Harness on a 2010 Nissan Xterra
- Step 4 in the instructions for wiring harness # C56225, linked for reference, seems to be where you are running into a little trouble. Before plugging in the harness to the vehicle behind that kick panel, you will need to insert the relays on the the connector.
On the other end of the 12 pin connector there are 3 ports, one for each of the relays. The brown one goes with the brown relay and the white plugs go with the blue relays. After you have plugged in everything you can tuck in the...
view full answer... - Location Of Kat's Heater Block Heater On 2008 Nissan Xterra
- For your 2008 Nissan Xterra, the Kat's Heaters Custom Engine Block Heater - Frost Plug Style - 120V - 400 Watts - 30 mm, # KH11412, will be installed in the left rear (driver's side). I've attached a picture to help.
view full answer... - Installing 7-Way Harness On 2012 Nissan Xterra
- I see from your recent order that you purchased the Tekonsha Primus IQ brake controller, part # TK90160 and the wiring harness adapter, part # 3050-P. You can simply plug one end of the adapter into the back of the brake controller and the other end into the port located under your dash near the emergency brake pedal and will be taped to another wiring harness.
The # 118266 you purchased will plug into the two connectors on the driver side frame rail near the back of the vehicle. You...
view full answer... - What Is Drop of Curt Channel Style Adjustable Ballmount # C45901 When in Tallest Drop Position
- When the platform of the Curt Channel Style Adjustable Ballmount # C45901 is in the drop position but up in the highest position possible the drop is right at 2 inches.
I attached a review video for this ball mount for you to check out as well.
view full answer... - Installing T-1 Harness, Part # 118263 on 2005 Xterra Without Tow Package
- In order to use the T-1 Harness, part # 118263 on an Xterra without the factory tow package, in addition to the relay, you will also need the jumper harness. The harness is a dealer supplied part.
Once you purchase the T-1, the relay, and the jumper harness you will have spent quite a few dollars, when you could purchase the Hopkins Custom Fit Vehicle Wiring Harness part # 43605. You would spend a bit more time installing it, but it would probably be less expensive.
view full answer... - Recommended Trailer Wiring for a 2008 Nissan Xterra Without a Factory Tow Package
- All of the functions on the 7-Way harness # 118266 will work with your 2008 Nissan Xterra without a factory 7-way wiring harness tow package.
I highly recommend using dielectric grease part # 11755 to help prevent corrosion from water exposure.
I included a couple FAQ's and installation video for you too.
view full answer... - How to Tell if 7-Way on 2013 Nissan Xterra is Fully Working
- The best way to tell that all of the functions on the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector # C56226 are working correctly is to use a circuit tester # PTW2992 and check all of the pins. I haven't heard of having to switch the blue and gray wires being a huge issue for installing this on your 2013 Nissan Xterra, but you can quickly double check all of the functions using the method I mentioned above. I'm also adding a photo showing what...
view full answer... - Installing Tekonsha Voyager Brkae Controller in 2013 Nissan Xterra S
- Since your 2013 Nissan Xterra S already has a 6/7-way trailer connector installed you can use the plug-n-play harness you referenced, part # 3050-P, to connect your Tekonsha Voyager Brake Controller, # 39510.
Since your Voyager plug has been cut off you will simply need to splice the four wires - black, white, blue and red - color for color to the wires exiting the back of your Voyager. You can use butt connectors # 05732-2 (you will need to order two sets for a total of four).
view full answer... - Replacement Mounting Hardware for 2012 Nissan Xterra Hitch Receiver
- There is different hardware available for each specific hitch and yes, you can purchase the hardware kit by itself. Since hitch receivers are custom fitted to vehicles, the hardware parts you receive will correlate with each receiver option for your 2012 Nissan Xterra.
The replacement Hardware Kit for Trailer Hitches is # RHK, but you will need to select your hitch item number and manufacturer when ordering to ensure you receive the proper hardware for your hitch. There is a box for...
view full answer... - How to Instal the Derale In-Line Fan Control Thermostat Part # D13021
- I can walk you through the installation process of the Derale In-Line Fan Control Thermostat with -6 AN Fittings part # D13021 but my instructions will be universal and not geared toward your 2007 Nissan Xterra, however, should be easy enough to adapt to your specification.
The fan control thermostat has an -6 AN fitting and the Derale Dyno-Cool Remote Cooler with Fan and Hose Barb Inlets part # D12743 has a barb fitting. Therefore, the thermostat will need to be installed in-line opposed...
view full answer... - Plug-N-Tow Vehicle Wiring Harness Vehicle Connection Location on a 2008 Nissan Xterra
- Wiring harness # 43605 plugs in behind the taillights, with an additional wire run to front of the vehicle to connect to the battery. You can refer to your owner's manual for information on how to access behind the taillights, (search under how to change bulb).
If your vehicle has the factory towing package, you need wiring harness 118263, the connection point on this harness runs along the frame on the driver's side. To view the install details, click on the provided link.
view full answer... - 2010 Nissan Xterra Brake Controller Wiring Harness Avalibility and Installation
- If your vehicle has the factory 7-Way wiring then the # 3050-P you referenced is correct and the connector is located underneath and left of the steering column, taped to another harness near the emergency brake pedal.
To install the Prodigy P2 # 90885 on a vehicle without the factory 7-Way wiring package, you will need the following parts.
T-One Vehicle Wiring Harness, item # 118263, If Not Already Present
Tekonsha Prodigy P2 Brake Controller, item # 90885
Brake Controller 7 & 4 Way...
view full answer... - Do All 6 Bolts Holes Need to be Used to Install Curt Adjustable Trailer Hitch on Smaller I-Beam
- According to step 3 of the linked installation instructions for the Adjustable Width Trailer Hitch Receiver # 13703 the 2 vertical mounting holes are only required if frame clearance permits. Since it sounds like you don't have the proper frame clearance it looks like you are good to just use the 4 horizontal bolt holes on either mounting bracket.
Please note that if you plan on using this for a non-trailer load like a bike rack or cargo carrier that Curt requires the use of a stabilizer...
view full answer... - Installing Trailer Wiring Harness on 2013 Nissan Xterra w/out Tow Package
- If your Xterra was not equipped with the factory tow package the port under the vehicle where the 4-pole trailer connector like part # C55441 plugs in will NOT be fully active. There is a jumper harness and relays that are needed to activate the tow package.
The Curt # C56225 that we offer includes the 4-pole that plugs into the connector along the drivers side frame rail alongside the spare tire, as well as the jumper harness and relays. The relays plug into the jumper harness, which...
view full answer... - Where to Run The Trailer Wiring Harness Out of the Passenger Compartment on a2005 Nissan Xterra
- Usually there is a grommet some where that can be utilized to route the trailer wiring out of the interior of the vehicle and mount it near the trailer hitch. When you access the rear of the left side tail light look for a grommet. Once you find one close enough that the 4-way connector can reach you will need to make a small slit in the grommet to put the 4 wires in and then route the connector through the hole and reinstall the grommet.
If you find a spot that you can use but it is not...
view full answer... - Removing the Spare Tire on a 2001 Nissan Xterra to Install a Trailer Hitch
- In the cargo area of the 2001 Nissan Xterra, under the carpet, there are tools for accessing and changing the spare tire. One of these tools is the jack rod. On one end of the jack rod there is a T-shape. Insert that end into the oval opening located above the license plate in the middle. The rod goes in at an angle so if you are looking at the back of the vehicle the end of the jack rod you are holding will be closer to the driver's side of the vehicle.
Then you will take the wheel nut...
view full answer... - Mounting Option for 7-Way Wiring Harness on 2005 Nissan Xterra with Curt Class III Trailer Hitch
- I have a mounting option for you, but the Curt Trailer Hitch, # 13514, does not have a built in mounting bracket for part # PK12711U. Instead, I recommend using our no-drill mounting bracket, part # C57202, along with the mounting bracket you referenced, # PK12711U. The no-drill bracket will wrap around the round tube crossmember of the hitch to provide a mounting point for the 7-way bracket.
view full answer... - Installation of Roadmaster MX or XL Base Plate On 2005 Nissan Xterra, and Parts Needed to Flat Tow
- No drilling is required to mount the Roadmaster MX Base Plate # RM-344-3B. To mount the XL Base Plate # 344-1B, a 1/2 inch hole will need to be drilled through the bumper core on each side. You will then use a 1/2 inch x 4-1/2 inch bolt, lock washer, and nut through the hole.
I have attached the installation instructions for both sets of base plates for you. The instructions for the Nissa Xterra begin on page 13 for both the XL and MX instructions.
The Roadmaster Tail Light Wiring Kit...
view full answer...
Go To Results